Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.

Vaktaðar vörur Skrá inn
Compact PICkit 3.5 programmer debugger board with USB connector and ICSP header, green PCB, black components

NuoTo

NuoTo PICkit 3.5 PIC Programmer Debugger Development Board

SKU CH-K4MA-K0J22

A PIC microcontroller programmer and in-circuit debugger with USB connection, supporting PIC16, PIC18, PIC24 and dsPIC series across a 1.8–5 V range

  • CPU TypeOther
  • Simulates and programs PIC microcontrollers via USB
  • Firmware self-recovery protects against upgrade failures
  • Supports PIC16, PIC18, PIC24 and dsPIC series
  • Operates from 1.8 V to 5 V for low-voltage targets
  • Diagnostic LEDs show power, activity and status

PICkit 3.5 programmer for PIC microcontrollers

The NuoTo PICkit 3.5 is a USB-connected in-circuit debugger and flash programmer built for students and engineers working with Microchip PIC devices. It supports MPLAB X IDE on Windows and targets almost all PIC families including PIC16, PIC18, PIC24 and dsPIC series. The kit includes adapter boards to simplify wiring during development.

Voltage range 1.8 to 5 volts decides target

The debugger operates from 1.8 V up to 5 V, matching the supply range of most PIC microcontrollers. Built-in over-voltage and short-circuit monitors protect both the tool and the target board during programming sessions. If your design runs outside this window, a different programmer is required.

USB plug-and-play with ICSP header and LED status

Connection uses a standard USB cable and the familiar 6-pin ICSP interface, so no external power supply is needed. Diagnostic LEDs show power, activity and status at a glance. The most common issue is a mismatched pin-out on custom boards — verify the ICSP header orientation before starting a debug session.

Helstu kostir

  • Simulates and programs PIC microcontrollers via USB
  • Firmware self-recovery protects against upgrade failures
  • Supports PIC16, PIC18, PIC24 and dsPIC series
  • Operates from 1.8 V to 5 V for low-voltage targets
  • Diagnostic LEDs show power, activity and status

Tæknilýsing

CPU TypeOther

Spurningar um þessa vöru

How does the PICkit 3.5 perform when it is inside a real development machine?

It connects through a full-speed USB port and uses Windows standard drivers, so the PC running MPLAB X IDE controls debugging and programming at the target processor's maximum speed.

What interface does the PICkit 3.5 use and what does that limit in practice?

The USB link provides full-speed communication with the host PC; the programmer itself handles targets from 1.8 V to 5 V and supports PIC16, PIC18, PIC24 and dsPIC series.

What does the board need to fit or mount in a typical setup?

It plugs into a USB port on the host computer and connects to the target PIC through an ICSP header, requiring only the supplied cables and a compatible pinout on the target board.

Einnig í þessum vöruflokki

Fólk bar þetta saman

Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.