暗号資産でのお支払いに対応—お手持ちのコインで、本物のハードウェアをご購入いただけます。暗号資産で支払い、本物のハードウェアに使う。 $399以上のご注文で、世界中どこでも送料無料（保険付き）。無地・ノーブランドの外箱で、ドイツから発送いたします。$399以上で送料無料（保険付き）。 注文手続きを開始すると、レートは30分間ロックされます。レートは30分間ロック。 すべての商品は未開封で、シリアル番号を確認した上で、24か月保証が付いています。未開封、24か月保証。

ウォッチリスト ログイン
Green printed circuit board with black memory chips and gold edge connectors

OWC

OWC 8GB DDR4 2400 CL17 1Rx8 260-pin 1.2V Non-ECC SODIMM memory upgrade for NCR POS CX7 (7772) CX8 (7736)

SKU CH-0D7C-XD3SY

An 8 GB DDR4 SODIMM running at 2400 MHz with CL17 timing, built for NCR POS CX7 (7772) and CX8 (7736) systems

  • Capacity8GB
  • Type260-Pin DDR4 Non-ECC SODIMM
  • SpeedDDR4 2400 (PC4 19200)
  • CAS LatencyCL17
  • Voltage1.2V
  • ECCNo
  • 8GB DDR4 2400 boosts multitasking speed for NCR CX7 and CX8 POS systems
  • CL17 latency at 1.2V delivers responsive operation with standard JEDEC timings
  • Single 1Rx8 260-pin SODIMM fits directly into the factory memory slot
  • JEDEC and RoHS compliant module ensures warranty-safe upgrade without compatibility risk
  • Unbuffered non-ECC design provides cost-effective capacity increase for point-of-sale workloads

OWC 8GB DDR4 SODIMM for NCR POS CX7 and CX8

This OWC module is an 8GB DDR4 2400 SODIMM built specifically for the NCR POS CX7 All-in-One POS (7772) and CX8 POS (7736). It provides a direct memory upgrade for those point-of-sale systems. The 260-pin form factor matches the slots in these units.

JEDEC-standard 1.2V operation with no heat spreader

The module runs at the standard DDR4 voltage of 1.2V and is unbuffered non-ECC with a CL17 latency. It carries no heat spreader, relying on the system's existing airflow. JEDEC and ROHS compliance ensures the upgrade is warranty-safe for the supported hardware.

Single 8GB 1Rx8 module at DDR4 2400 PC4-19200

This kit consists of one 8GB stick organised as 1Rx8, rated for DDR4 2400 (PC4-19200). It adds exactly eight gigabytes of capacity; systems requiring a matched pair or a larger total capacity will need additional modules.

特長

  • 8GB DDR4 2400 boosts multitasking speed for NCR CX7 and CX8 POS systems
  • CL17 latency at 1.2V delivers responsive operation with standard JEDEC timings
  • Single 1Rx8 260-pin SODIMM fits directly into the factory memory slot
  • JEDEC and RoHS compliant module ensures warranty-safe upgrade without compatibility risk
  • Unbuffered non-ECC design provides cost-effective capacity increase for point-of-sale workloads

仕様

BrandOWC
Part Number2S4D41R808GB
Capacity8GB
Type260-Pin DDR4 Non-ECC SODIMM
SpeedDDR4 2400 (PC4 19200)
CAS LatencyCL17
Voltage1.2V
ECCNo
Buffered/RegisteredUnbuffered
Rank1Rx8
Heat SpreaderNo
Compatible SystemNCR POS CX7 All-in-One POS (7772)
NCR POS CX8 POS (7736)

このモデルの他のバージョン

同シリーズにさらに 5点

同じファミリーで、メモリ・クーラー・クロックが異なります — 購入前に比較してください。

この商品に関する質問

How do I install the 260-pin SODIMM in my NCR POS CX7 (7772) and what step is often missed?

Power off the terminal, unplug it, open the memory access panel, align the notch on the module with the slot key, press firmly until both side clips click shut, then verify the new 8GB appears in BIOS before closing the case.

What maintenance or replacement will this DDR4 module need over its service life?

No scheduled maintenance is required; the module has no heat spreader and no moving parts, so replacement is only necessary if a memory test reports errors or the system fails to recognise the 8GB capacity.

What limit appears first when the POS CX8 (7736) runs sustained workloads with this CL17 memory?

The CAS latency of 17 cycles at 2400 MT/s sets the baseline access delay; under continuous load the memory controller will hit that timing wall before bandwidth or voltage headroom becomes a bottleneck.

同じ売り場の商品

よく比較されている商品

同じ売り場、同じレジ — 8種類のコインと30分間のレートロック。