暗号資産でのお支払いに対応—お手持ちのコインで、本物のハードウェアをご購入いただけます。暗号資産で支払い、本物のハードウェアに使う。 $399以上のご注文で、世界中どこでも送料無料（保険付き）。無地・ノーブランドの外箱で、ドイツから発送いたします。$399以上で送料無料（保険付き）。 注文手続きを開始すると、レートは30分間ロックされます。レートは30分間ロック。 すべての商品は未開封で、シリアル番号を確認した上で、24か月保証が付いています。未開封、24か月保証。

ウォッチリスト ログイン
Green circuit board with gold edge connectors and black memory chips

OWC

OWC 8GB DDR4 2666 CL19 1Rx8 288-pin 1.2V Non-ECC UDIMM memory upgrade

SKU CH-FGH9-MGW0J

Adds 8 GB of DDR4 2666 CL19 UDIMM memory to compatible QNAP NAS models including TS-h1277XU-RP, TS-h1677XU-RP, TS-h2477XU-RP and TS-h977XU-RP

  • Capacity8GB
  • Type288-Pin DDR4 Non-ECC UDIMM
  • SpeedDDR4 2666 (PC4 21300)
  • CAS LatencyCL19
  • Voltage1.2V
  • ECCNo
  • Boosts QNAP NAS capacity with 8GB DDR4 2666 CL19 module
  • JEDEC and RoHS compliant for warranty-safe upgrade
  • Low 1.2V voltage reduces power draw and heat
  • Backward compatible with 2133 and 2400MHz systems
  • Simple DIY installation fits 288-pin UDIMM slots

8GB DDR4 2666 UDIMM for QNAP NAS

This single 8GB DDR4 2666 module is built for the QNAP TS-h1277XU-RP, TS-h1677XU-RP, TS-h2477XU-RP and TS-h977XU-RP. It delivers a straightforward capacity increase for those NAS units without requiring ECC or registered memory. The non-ECC unbuffered design matches the original specification for these systems.

Thermals and power at 1.2V

Operating at 1.2V, the module runs cool without a heat spreader and draws minimal power during typical NAS workloads. JEDEC-standard timings of CL19 at 2666MHz keep latency predictable while the low voltage limits heat output inside the chassis. Silent operation is inherent with no moving parts to generate noise.

Fits 288-pin DDR4 slots with backward speed support

The 288-pin UDIMM form factor slots directly into compatible QNAP bays and requires no tools beyond opening the case. Backward compatibility with 2133MHz and 2400MHz systems allows the module to downclock automatically if the platform demands it. One DIMM per slot leaves remaining channels free for further expansion.

特長

  • Boosts QNAP NAS capacity with 8GB DDR4 2666 CL19 module
  • JEDEC and RoHS compliant for warranty-safe upgrade
  • Low 1.2V voltage reduces power draw and heat
  • Backward compatible with 2133 and 2400MHz systems
  • Simple DIY installation fits 288-pin UDIMM slots

仕様

BrandOWC
Part Number2U6D41R808GB
Capacity8GB
Type288-Pin DDR4 Non-ECC UDIMM
SpeedDDR4 2666 (PC4 21300)
CAS LatencyCL19
Voltage1.2V
ECCNo
Buffered/RegisteredUnbuffered
Rank1Rx8
Heat SpreaderNo
Compatible SystemQNAP TS-h1277XU-RP
QNAP TS-h1677XU-RP
QNAP TS-h2477XU-RP
QNAP TS-h977XU-RP

このモデルの他のバージョン

同シリーズにさらに 5点

同じファミリーで、メモリ・クーラー・クロックが異なります — 購入前に比較してください。

この商品に関する質問

How do I install this 288-pin DDR4 UDIMM in my QNAP TS-h1277XU-RP and what step is often missed?

Power off the NAS, open the chassis, align the notch on the module with the slot key, press firmly until both retention clips click, then verify the new 8 GB appears in the system BIOS before closing the case.

What maintenance or replacement will this non-ECC 1Rx8 module need over time?

No scheduled maintenance is required; the module has no heat spreader or moving parts, so replacement is only necessary if a memory test reports errors or capacity needs increase.

What limit appears first when this CL19 2666 MHz stick runs sustained workloads?

The CAS latency of 19 cycles at 2666 MHz sets the response-time floor, so latency-sensitive tasks hit that timing ceiling before bandwidth or voltage limits become a factor.

同じ売り場の商品

よく比較されている商品

同じ売り場、同じレジ — 8種類のコインと30分間のレートロック。