暗号資産でのお支払いに対応—お手持ちのコインで、本物のハードウェアをご購入いただけます。暗号資産で支払い、本物のハードウェアに使う。 $399以上のご注文で、世界中どこでも送料無料（保険付き）。無地・ノーブランドの外箱で、ドイツから発送いたします。$399以上で送料無料（保険付き）。 注文手続きを開始すると、レートは30分間ロックされます。レートは30分間ロック。 すべての商品は未開封で、シリアル番号を確認した上で、24か月保証が付いています。未開封、24か月保証。

ウォッチリスト ログイン
Black 80mm blower fan 18mm thick three pin connector

Zyvpee

Zyvpee BG0801-B045-00S 80*18mm 12V .34A 3-pin blower case fan

SKU CH-RDQY-ZWYWY

An 80 by 18 millimetre 12-volt 0.34-amp blower fan with ball bearing and three-pin connector

  • TypeCase Fan
  • Bearing TypeBall
  • Power Connector3 wires
  • ColorBlack
  • LEDNon-LED
  • FeaturesDC Blower
  • NMB 8018 blower design directs airflow through tight chassis spaces
  • 12 V 0.34 A draw keeps power load low for compact builds
  • Ball bearing construction extends operating life in continuous use
  • 3-pin connector enables direct motherboard speed control
  • 80 x 18 mm frame fits standard 80 mm mounting points

Compact blower for tight builds

This Zyvpee blower-style case fan measures 80 by 18 millimetres and runs on 12 volts at 0.34 amps. Its three-pin connector and ball bearing suit small-form-factor chassis, projectors or industrial enclosures that need directed airflow rather than broad circulation.

Replaces noisy sleeve-bearing blowers

When an existing 80-millimetre blower develops rattle or loses pressure, this unit restores focused cooling without changing mounting points. The jump is worth it if the current fan uses sleeve bearings or a two-pin header and you need the third wire for speed reporting.

Fits 80-millimetre blower mounts

The 80-by-18-millimetre frame slides into standard blower cut-outs and the three-pin lead plugs into any compatible motherboard or fan controller header. Ball-bearing construction reduces maintenance intervals, freeing up service time for the rest of the build.

特長

  • NMB 8018 blower design directs airflow through tight chassis spaces
  • 12 V 0.34 A draw keeps power load low for compact builds
  • Ball bearing construction extends operating life in continuous use
  • 3-pin connector enables direct motherboard speed control
  • 80 x 18 mm frame fits standard 80 mm mounting points

仕様

SeriesBG0801-B045-00S
ModelBG0801-B045-00S
TypeCase Fan
Bearing TypeBall
Power Connector3 wires
ColorBlack
LEDNon-LED
FeaturesDC Blower
Dimensions80*18mm

この商品に関する質問

Will the 80 by 18 mm blower fit my projector or small-form-factor case?

The fan measures 80 mm square and 18 mm thick, so it fits any 80 mm mounting pattern with at least 18 mm clearance behind the housing.

How do I connect the three-wire lead to a standard motherboard header?

Plug the 3-pin connector onto a 12 V fan header; the third wire carries the tachometer signal so the board can monitor speed.

When should I expect to replace the ball-bearing blower?

Ball bearings typically run for tens of thousands of hours; listen for new rattling or a drop in airflow as signs the fan needs swapping.

同じ売り場の商品

よく比較されている商品

同じ売り場、同じレジ — 8種類のコインと30分間のレートロック。