저희는 암호화폐로 결제를 받습니다 — 보유하신 코인으로 실제 하드웨어를 구매하실 수 있습니다.암호화폐로 결제하고, 실제 하드웨어 구매에 사용하십시오. 전 세계 어디서나 US$399 이상 구매 시 무료 보험 배송. 무지 상자에 담아 독일에서 발송합니다.US$399 이상 구매 시 무료 보험 배송. 체크아웃을 시작하면 30분 동안 환율이 잠깁니다.30분간 환율 잠금. 모든 제품은 밀봉된 상태로 일련번호를 확인한 후 24개월 보증을 제공합니다.밀봉 포장, 24개월 보증.

가격 추적 로그인
Pre-bent brass tube, 13 mm OD, deep black gloss finish, 90 degree bend with 30 cm and 10 cm legs

Alphacool

Alphacool Brass HardTube 13mm OD 90° Deep Black 10/30cm

SKU CH-KXNY-WY5HN

Pre-bent 90° brass tubing with 13 mm outer diameter, 12.2 mm inner diameter and 0.8 mm wall thickness in Deep Black, supplied as 30 cm and 10 cm lengths for custom liquid-cooling loops

  • TypeTubing

Color Black

  • Brass tubing resists corrosion in liquid cooling loops
  • 90 degree bend fits tight routing without extra fittings
  • 8 mm wall thickness balances strength with easy cutting
  • Deep Black gloss coating resists scratches and chipping
  • 13 mm outer diameter matches standard hard-tube fittings

Brass HardTube 90° 13mm OD

This pre-bent brass tube provides a 90-degree corner for custom liquid-cooling loops. The 13 mm outer diameter matches standard hard-tube fittings. Deep black gloss coating resists scratches under normal handling. It suits builders who want rigid tubing aesthetics without bending tools.

Install with deburring step

Cut ends must be smoothed with fine sandpaper or a deburrer before assembly. Sharp edges left from cutting will damage fitting O-rings and cause leaks. The .8 mm wall is rigid yet thin enough to saw by hand without powered equipment. No heat bending is required because the angle is factory-formed.

Fixed 10/30 cm legs

The 30 cm and 10 cm straight sections set the exact offset between components. Loops needing longer reach or a different bend radius cannot use this part. Inner diameter of 12.2 mm supports typical coolant flow rates for CPU and GPU blocks. Builders requiring extended runs must add straight tubing sections.

주요 특징

  • Brass tubing resists corrosion in liquid cooling loops
  • 90 degree bend fits tight routing without extra fittings
  • 8 mm wall thickness balances strength with easy cutting
  • Deep Black gloss coating resists scratches and chipping
  • 13 mm outer diameter matches standard hard-tube fittings

사양

TypeTubing

이 모델의 다른 버전

같은 라인업에서 5개 더

같은 제품군에서 메모리·쿨러·클럭이 다릅니다 — 결정 전에 비교해 보세요.

이 상품에 대한 질문

How do I confirm the Alphacool Brass HardTube 13mm OD 90° Deep Black is seated correctly after installation?

After fitting the 90 degree brass tube with its 13 mm outer diameter and 12.2 mm inner diameter, run the loop under pressure and check every joint for leaks; the 0.8 mm wall thickness and gloss black coating should show no deformation or coating damage at the fittings.

What comes with the Alphacool Brass HardTube 18607 and which parts must be sourced separately?

The package contains one pre-bent 90 degree brass tube with a 30 cm long side and a 10 cm short side; compatible 13 mm compression fittings, deburring tool, cutting tool and coolant are not included and must be purchased separately.

Which length variant of the Alphacool Brass HardTube 13mm OD 90° should I choose for my loop?

This version provides a fixed 30 cm long leg and a 10 cm short leg; select it when your bend geometry matches those exact dimensions, otherwise choose a straight tube or a different pre-bent length from the Alphacool range.

이 진열대의 다른 상품

고객들이 함께 비교한 상품

같은 진열대, 같은 체크아웃 — 코인 8종, 환율 잠금 30분.