저희는 암호화폐로 결제를 받습니다 — 보유하신 코인으로 실제 하드웨어를 구매하실 수 있습니다.암호화폐로 결제하고, 실제 하드웨어 구매에 사용하십시오. 전 세계 어디서나 US$399 이상 구매 시 무료 보험 배송. 무지 상자에 담아 독일에서 발송합니다.US$399 이상 구매 시 무료 보험 배송. 체크아웃을 시작하면 30분 동안 환율이 잠깁니다.30분간 환율 잠금. 모든 제품은 밀봉된 상태로 일련번호를 확인한 후 24개월 보증을 제공합니다.밀봉 포장, 24개월 보증.

가격 추적 로그인
Green Arduino shield board with four black relay modules and indicator LEDs

Arduino

Arduino 4 Relays Shield development board

SKU CH-8W5F-8CTFX

Adds four parallel relay channels with NO/NC contacts and status LEDs to switch high-power loads from an Arduino board

  • Controls high-power loads beyond Arduino I/O limits
  • Four relays with parallel changeover contacts for higher current
  • Each relay provides normally open and normally closed contacts
  • Four status LEDs show real-time relay on/off state
  • Shield format plugs directly onto compatible Arduino boards

High-Power Load Control

The Arduino 4 Relays Shield enables an Arduino board to switch high-power loads that exceed the current and voltage limits of its digital I/O pins. It provides four independent relay channels, each featuring two pole changeover contacts with normally open and normally closed configurations. The dual contacts are wired in parallel to increase the current-handling capability of each output. Four onboard LEDs give immediate visual indication of the on/off state for every relay.

Stackable Shield Format

The shield mounts directly onto a compatible Arduino board using standard header pins, requiring no separate wiring harness or external power supply for the relay coils. This plug-in design keeps the prototype compact and allows additional shields to be stacked above if needed. The integrated status LEDs remove the need for external monitoring circuitry during development, simplifying test bench setups for automation or IoT edge applications.

Relay Terminal Access

Each relay channel exposes its changeover contacts through screw terminals, supporting secure connections for mains-voltage or high-current wiring without soldering. The parallel contact arrangement boosts the switching rating per channel while maintaining isolation between the control logic and the load circuit. Builders who require more than four switched circuits or need solid-state switching speeds will need a different module. The board is supplied new and ready for immediate integration.

주요 특징

  • Controls high-power loads beyond Arduino I/O limits
  • Four relays with parallel changeover contacts for higher current
  • Each relay provides normally open and normally closed contacts
  • Four status LEDs show real-time relay on/off state
  • Shield format plugs directly onto compatible Arduino boards

사양

이 상품에 대해 아직 공개된 사양이 없습니다.

이 상품에 대한 질문

Will the relay contacts on this shield need replacement after many switching cycles?

The shield uses four electromechanical relays with paralleled changeover contacts; contact wear over high cycle counts is normal for this type of relay and may eventually require shield replacement.

What limits continuous operation when all four relays are energised?

Each relay draws coil current while active, so sustained use with all four on increases total board power draw and heat, which can become the limiting factor in enclosed installations.

How much heat and noise does the shield produce when running all day?

Four energised relay coils generate modest heat and each relay clicks audibly when switching; with constant activation the board warms slightly but has no fan, so noise is limited to the switching clicks.

이 진열대의 다른 상품

고객들이 함께 비교한 상품

같은 진열대, 같은 체크아웃 — 코인 8종, 환율 잠금 30분.