저희는 암호화폐로 결제를 받습니다 — 보유하신 코인으로 실제 하드웨어를 구매하실 수 있습니다.암호화폐로 결제하고, 실제 하드웨어 구매에 사용하십시오. 전 세계 어디서나 US$399 이상 구매 시 무료 보험 배송. 무지 상자에 담아 독일에서 발송합니다.US$399 이상 구매 시 무료 보험 배송. 체크아웃을 시작하면 30분 동안 환율이 잠깁니다.30분간 환율 잠금. 모든 제품은 밀봉된 상태로 일련번호를 확인한 후 24개월 보증을 제공합니다.밀봉 포장, 24개월 보증.

가격 추적 로그인
Green rectangular PCB with rows of screw terminals and pin headers along the edges, status LEDs near the centre

KEHIPI

KEHIPI FNK0091 Breakout Board for Freenove ESP32 / ESP32-S3

SKU CH-GHBH-385N6

Breakout board with terminal blocks and pin headers exposes every GPIO on compatible Freenove ESP32 and ESP32-S3 boards, adds 5 V and 3.3 V power rails up to 3 A.

  • Plug in Freenove ESP32 boards for instant GPIO breakout
  • See pin state at a glance with on-board status LEDs
  • LEDs driven by the chip so GPIOs stay unaffected
  • Get multiple 5 V and 3.3 V rails, 5 V up to 3 A with external supply
  • Screw terminals and 2.54 mm headers expose every pin

Purpose-built breakout for Freenove ESP32 boards

The KEHIPI FNK0091 breakout board gives Freenove ESP32 and ESP32-S3 developers a solder-free way to reach every GPIO. It plugs directly onto compatible Freenove modules such as the FNK0060, FNK0090, FNK0085 and FNK0099. A 2.54 mm pitch terminal block and matching header expose all pins for quick wiring. An on-board LED driven by the chip shows logic state without loading the GPIO.

Makers who need fast GPIO access on supported

This shield suits hobbyists, educators and prototype engineers who already own a listed Freenove board and want instant access to power rails and signal pins. Builders using ESP32 or ESP32-S3 boards from other vendors cannot use this HAT because the pinout differs. Projects that demand a different form factor or integrated wireless antennas should look at other hardware.

Pinout locked to Freenove ESP32 / ESP32-S3 series

The single specification that decides fit is the pin arrangement: this breakout matches only the Freenove ESP32-WROVER, ESP32-WROOM, ESP32-S3-WROOM and ESP32-S3-WROOM Lite boards listed above. Any other module, even with the same chip, will not align with the 2.54 mm terminal block and header. Verify your board model before purchase.

주요 특징

  • Plug in Freenove ESP32 boards for instant GPIO breakout
  • See pin state at a glance with on-board status LEDs
  • LEDs driven by the chip so GPIOs stay unaffected
  • Get multiple 5 V and 3.3 V rails, 5 V up to 3 A with external supply
  • Screw terminals and 2.54 mm headers expose every pin

사양

BrandFREENOVE
ModelFNK0091
Part NumberFNK0091

이 상품에 대한 질문

Which Freenove ESP32 board must I already own to use the FNK0091 breakout?

The FNK0091 works with Freenove ESP32-WROVER board FNK0060, ESP32-WROOM board FNK0090, ESP32-S3-WROOM board FNK0085 or ESP32-S3-WROOM Lite board FNK0099.

Will the 2.54 mm terminal blocks on this HAT still let me connect older 0.1 inch sensors?

Yes, the 2.54 mm pitch matches the 0.1 inch standard so existing sensors plug straight into the terminal blocks.

How can I verify the GPIO LEDs are showing live pin state after I power up?

Each LED lights when its GPIO reads high and stays off when the pin reads low; the LEDs are driven independently so they never load the GPIO.

이 진열대의 다른 상품

고객들이 함께 비교한 상품

같은 진열대, 같은 체크아웃 — 코인 8종, 환율 잠금 30분.