저희는 암호화폐로 결제를 받습니다 — 보유하신 코인으로 실제 하드웨어를 구매하실 수 있습니다.암호화폐로 결제하고, 실제 하드웨어 구매에 사용하십시오. 전 세계 어디서나 US$399 이상 구매 시 무료 보험 배송. 무지 상자에 담아 독일에서 발송합니다.US$399 이상 구매 시 무료 보험 배송. 체크아웃을 시작하면 30분 동안 환율이 잠깁니다.30분간 환율 잠금. 모든 제품은 밀봉된 상태로 일련번호를 확인한 후 24개월 보증을 제공합니다.밀봉 포장, 24개월 보증.

가격 추적 로그인
Small rectangular ABS case with rounded edges, dull matte finish, one RJ45 port and three USB ports visible

LORDWORLD

LORDWORLD ETH-USB-HUB-BOX development board with ABS case

SKU CH-E56F-F0TQ9

Adds one 10/100M Ethernet port and three USB 2.0 ports to Raspberry Pi Zero boards via pogo pins inside a snap-fit ABS case

  • Adds wired network access via 10/100M Ethernet port
  • Expands connectivity with three USB 2.0/1.1 ports
  • Attaches directly using pogo pins for Zero boards
  • Protected by ABS case with two interchangeable lids
  • Rounded edges and dull polish finish resist fingerprints

Raspberry Pi Zero HAT with Ethernet

The LORDWORLD ETH-USB-HUB-BOX adds wired networking and three USB ports to any Raspberry Pi Zero series board. It connects through a pogo-pin interface that requires no soldering or cables. An RTL8152B chip provides a single RJ45 port with 10/100M auto-negotiation. The board fits inside an ABS enclosure with a snap-on lid.

Upgrading from USB-only Zero boards

Makers who have relied on USB-Ethernet dongles or Wi-Fi can replace those adapters with this integrated HAT. The jump is worth it when a project needs a stable wired link and extra USB sockets without occupying the Pi's only USB port. It also removes the mechanical strain of dangling dongles on portable builds.

Three USB 2.0 ports and 100M Ethernet headroom

The hub comfortably handles keyboards, mice, flash drives and other USB 2.0 or 1.1 peripherals simultaneously. Bandwidth tops out at 100M on the Ethernet side, so sustained gigabit transfers are not possible. Projects that need faster networking or more than three downstream USB devices will need a different solution.

주요 특징

  • Adds wired network access via 10/100M Ethernet port
  • Expands connectivity with three USB 2.0/1.1 ports
  • Attaches directly using pogo pins for Zero boards
  • Protected by ABS case with two interchangeable lids
  • Rounded edges and dull polish finish resist fingerprints

사양

BrandLORDWORLD

이 상품에 대한 질문

Will the ABS case fit a Raspberry Pi Zero WH with the pogo-pin header attached?

Yes, the pogo-pin design connects directly to Raspberry Pi Zero, Zero W, Zero WH, 2 W and 2 WH boards without soldering.

How do I install the board and avoid the common pogo-pin misalignment?

Align the pogo pins with the Zero's GPIO pads, press the board down evenly until the pins seat, then snap the chosen lid onto the ABS case.

If the RTL8152B Ethernet chip fails, can I replace just that component?

The chip is soldered to the HAT; replacement requires board-level rework, so the usual remedy is to swap the entire HAT.

이 진열대의 다른 상품

고객들이 함께 비교한 상품

같은 진열대, 같은 체크아웃 — 코인 8종, 환율 잠금 30분.