Western Digital
Western Digital WD1002FBYS 1TB 7200 RPM 32MB SATA 3.0Gb/s 3.5" internal hard drive
A 1 TB 3.5″ SATA desktop drive with 7200 RPM, 32 MB cache and dual-processor design for enterprise workloads
- PackagingBare Drive
- Capacity1TB
- RPM7200 RPM
- InterfaceSATA 3.0Gb/s
- Cache32MB
- Average Latency4.2ms
- Dual processor boosts performance by 20%
- 7200 RPM and 32MB cache for fast access
- StableTrac secures motor shaft at both ends to cut vibration
- RAFF technology corrects vibration in real time for 60% gain in high-vibration settings
- TLER prevents drive fallout during RAID error recovery
Enterprise-grade storage drive
The Western Digital RE3 WD1002FBYS is a 1 TB 3.5-inch internal hard drive built for servers and storage arrays. It spins at 7200 RPM with a 32 MB cache and a SATA 3.0Gb/s interface. A dual-processor design delivers a 20% performance improvement over the previous generation.
Vibration-resistant integration
The drive fits a standard 3.5-inch bay and connects via SATA data and power cables. StableTrac secures the motor shaft at both ends to cut system-induced vibration. Fourth-generation RAFF technology monitors and corrects linear and rotational vibration in real time, yielding a 60% improvement in high-vibration environments over the previous generation. TLER limits error-recovery time to prevent drive fallout in RAID arrays.
Sustained workload behaviour
Average latency sits at 4.2 ms under continuous operation. The vibration-correction features maintain throughput when multiple drives share a chassis. Units are supplied as bare drives, erased to DoD 5220.22-M standard, and may show up to 25 bad sectors or cosmetic label differences. Not suited for buyers who need a formatted, partitioned volume out of the box or who require a newer interface than SATA 3.0Gb/s.
Pluspunten
- Dual processor boosts performance by 20%
- 7200 RPM and 32MB cache for fast access
- StableTrac secures motor shaft at both ends to cut vibration
- RAFF technology corrects vibration in real time for 60% gain in high-vibration settings
- TLER prevents drive fallout during RAID error recovery
Specificaties
| Brand | Western Digital |
|---|---|
| Series | RE3 |
| Model | WD1002FBYS |
| Packaging | Bare Drive |
| Capacity | 1TB |
| RPM | 7200 RPM |
| Interface | SATA 3.0Gb/s |
| Cache | 32MB |
| Average Latency | 4.2ms |
| Form Factor | 3.5" |
| Features | Dual processor - Twice the processing power results in a 20% performance improvement over the previous generation. StableTrac - The motor shaft is secured at both ends to reduce system-induced vibration and stabilize platters for accurate tracking during read and write operations RAID-specific, time-limited error recovery (TLER) - Prevents drive fallout caused by the extended hard drive error-recovery processes common to desktop drives. NoTouch ramp load technology - The recording head never touches the disk media ensuring significantly less wear to the recording head and media as we |
| Verzendgewicht | 0.73 kg |
| Pakketafmetingen | 152 × 102 × 25 mm |
Vragen over dit artikel
How long is the average latency before data transfers begin?
The average latency is 4.2 ms before the drive can start transferring data.
Does the dual-processor design increase heat or noise during continuous operation?
The dual processor improves performance by 20 percent without increasing acoustic or thermal output.
What SATA host interface must the system provide for this 3.5 inch drive?
The drive requires a SATA 3.0 Gb/s host port and standard 3.5 inch power and data cables.
Ook in deze afdeling
Klanten vergeleken ook
Dezelfde afdeling, dezelfde kassa — acht munten en een koers die 30 minuten vaststaat.
