Akceptujemy kryptowaluty — posiadane środki można więc wykorzystać na zakup prawdziwego sprzętu.Płatność kryptowalutą — realny sprzęt w zamian. Bezpłatna, ubezpieczona dostawa na całym świecie powyżej 399 $. Neutralne kartony, bez oznaczeń, wysyłane z Niemiec.Bezpłatna, ubezpieczona dostawa powyżej 399 $. Kurs zostaje zablokowany na 30 minut od otwarcia kasy.Kurs zablokowany na 30 minut. Każdy produkt jest fabrycznie zapieczętowany, jego numer seryjny jest sprawdzany, a całość objęta jest 24-miesięczną gwarancją.Zapieczętowane fabrycznie, 24 miesiące gwarancji.

Obserwowane produkty Zaloguj się
Adafruit 75mm slide potentiometer with white-striped knob on silver metal track

Adafruit

Adafruit Slide Potentiometer 75mm 10K Ohm engineering development tool

SKU CH-P2EX-SP0N1

A 75mm linear slide potentiometer with a 10K ohm resistance and included knob, suited for breadboarding and prototyping

  • TypePrototyping Products
  • 75 mm travel lets you set levels by sight
  • 10 kΩ linear taper gives predictable voltage division
  • 15 mm shank fits standard breadboard spacing
  • Supplied knob with white stripe shows position at a glance
  • 5 mm wide body leaves room for adjacent components

Adafruit 75mm Slide Potentiometer

The Adafruit slide potentiometer is a linear 10K ohm variable resistor with a 75mm travel distance. It includes a grippy plastic knob marked with a white stripe for visual position reference. The component suits breadboarding and prototyping work where a sliding control is preferred over a rotary design.

For prototyping and audio-style controls

Engineers and hobbyists building mixers, synthesiser modules or test jigs will appreciate the smooth sliding action and included knob. Builders who need a sealed, multi-turn or motorised potentiometer should look at other component types because this is a standard single-turn slide pot.

Check mounting and wiring before ordering

The shank measures 15mm long and 4mm wide while the nub dimensions are 11.2mm by 7mm by 9.3mm. Verify that your breadboard or perfboard hole spacing accepts these dimensions and that a 10K ohm linear taper matches your circuit requirements.

Najważniejsze cechy

  • 75 mm travel lets you set levels by sight
  • 10 kΩ linear taper gives predictable voltage division
  • 15 mm shank fits standard breadboard spacing
  • Supplied knob with white stripe shows position at a glance
  • 5 mm wide body leaves room for adjacent components

Specyfikacja

TypePrototyping Products

Pytania dotyczące tego produktu

What breadboard spacing do I need for the three legs of this 10K ohm linear slide potentiometer?

The legs fit a standard solderless breadboard or a perfboard with large holes; the shank is 15mm long and 4mm wide, and the nub measures 11.2 x 7 x 9.3mm, so check your board hole pitch before soldering.

Will the 75mm long slide potentiometer sit flush next to older through-hole components on my prototype board?

Its body is 9.5mm wide and 6.5mm high with a 15mm shank, so it occupies a similar footprint to many classic through-hole pots; leave a little clearance for the knob that ships with it.

How can I confirm the slide potentiometer is giving a smooth linear response after I wire it as a voltage divider?

Measure the output voltage while sliding the knob from one end to the other; a steady, proportional change from low to high across the 75mm travel shows the 10K ohm linear element is working as intended.

Także w tym dziale

Klienci porównywali też te produkty

Ten sam dział, ta sama kasa — osiem kryptowalut i 30-minutowa blokada kursu.