Akceptujemy kryptowaluty — posiadane środki można więc wykorzystać na zakup prawdziwego sprzętu.Płatność kryptowalutą — realny sprzęt w zamian. Bezpłatna, ubezpieczona dostawa na całym świecie powyżej 399 $. Neutralne kartony, bez oznaczeń, wysyłane z Niemiec.Bezpłatna, ubezpieczona dostawa powyżej 399 $. Kurs zostaje zablokowany na 30 minut od otwarcia kasy.Kurs zablokowany na 30 minut. Każdy produkt jest fabrycznie zapieczętowany, jego numer seryjny jest sprawdzany, a całość objęta jest 24-miesięczną gwarancją.Zapieczętowane fabrycznie, 24 miesiące gwarancji.

Obserwowane produkty Zaloguj się
Stainless steel nozzle cleaning kit with ten 0.4mm needles in a bottle and one angled tweezer

Aokin 19-3 12 Pcs 3D Printer Nozzle Cleaning Kit - 10 Pcs 0.4mm Needles and Tweezers

SKU CH-GH55-97T75

Clears clogged 0.4 mm nozzles with ten stainless-steel needles and a curved tweezer for precise maintenance

  • Color12 Pcs
  • Type19-3
  • Clears clogged 0.4 mm nozzles with 10 precision needles
  • Stainless-steel needles resist bending and breaking during use
  • Curved tweezers reach tight spots to remove support material
  • Compatible with popular printers including Creality and Prusa models
  • 12-piece kit supplies both needles and tweezers in one pack

12-piece nozzle cleaning kit for 0.4 mm printers

The Aokin 19-3 kit supplies ten stainless-steel needles of 0.4 mm diameter and one angled tweezer for clearing filament residue. Both tools are made from corrosion-resistant stainless steel so they withstand repeated heating cycles. The needles measure 7 cm overall with a 3 cm shank, while the tweezer spans 12 cm for reach into tight extruder assemblies. The set arrives new in a protective bottle.

Replaces clogged-nozzle downtime

Instead of using drills, guitar strings or single-use needles, this kit gives a repeatable cleaning method for 0.4 mm nozzles on machines such as Creality Ender 3, Prusa i3, Anet A8 and E3D hot-ends. The jump is worth it when a blocked nozzle halts a print run and a quick, heated clean at over 200 degrees restores flow without disassembly. The curved tweezer tip also removes support remnants from feeder gears and throats in one motion.

Suits hobbyists and small-shop operators running

Makers who print daily on standard 0.4 mm nozzles will value the durable needles and precise tweezer for routine maintenance. Users with larger-diameter nozzles, hardened-steel or ruby tips, or fully enclosed high-temperature chambers should look elsewhere because the 0.4 mm needles cannot pass wider orifices and the tools are not rated for exotic abrasive filaments. Parents must store the sharp pieces away from children.

Najważniejsze cechy

  • Clears clogged 0.4 mm nozzles with 10 precision needles
  • Stainless-steel needles resist bending and breaking during use
  • Curved tweezers reach tight spots to remove support material
  • Compatible with popular printers including Creality and Prusa models
  • 12-piece kit supplies both needles and tweezers in one pack

Specyfikacja

BrandAokin
Model19-3
Part Number19-3
Color12 Pcs
Type19-3

Pytania dotyczące tego produktu

Will the 0.4 mm needles fit a standard 0.4 mm nozzle on an Ender 3?

Yes, the kit is compatible with most 0.4 mm extruder nozzles including Creality Ender 3, CR-10, Prusa i3 and other listed models.

Do I need to heat the hotend before pushing the 7 cm needles through?

Heat the nozzle above 200 degrees before using the needles; inserting them cold can damage the tip or snap the needle.

How often should I replace the 10 stainless-steel needles?

Replace needles when the 0.4 mm tips become bent, blunt or corroded; the stainless steel resists wear but fine tips degrade with repeated high-temperature use.

Także w tym dziale

Klienci porównywali też te produkty

Ten sam dział, ta sama kasa — osiem kryptowalut i 30-minutowa blokada kursu.