Akceptujemy kryptowaluty — posiadane środki można więc wykorzystać na zakup prawdziwego sprzętu.Płatność kryptowalutą — realny sprzęt w zamian. Bezpłatna, ubezpieczona dostawa na całym świecie powyżej 399 $. Neutralne kartony, bez oznaczeń, wysyłane z Niemiec.Bezpłatna, ubezpieczona dostawa powyżej 399 $. Kurs zostaje zablokowany na 30 minut od otwarcia kasy.Kurs zablokowany na 30 minut. Każdy produkt jest fabrycznie zapieczętowany, jego numer seryjny jest sprawdzany, a całość objęta jest 24-miesięczną gwarancją.Zapieczętowane fabrycznie, 24 miesiące gwarancji.

Obserwowane produkty Zaloguj się
Four clear acrylic tubes bent at 90 degrees with straight sections 110mm and 415mm long, 16mm outer diameter

Bitspower

Bitspower Pre-bent 90° Acrylic Hard Tube OD16mm 110x415mm 4pcs

SKU CH-EMY7-GR48R

Pre-bent 90° acrylic hard tube with 110 mm and 415 mm straight sections, 16 mm outer diameter, four pieces for custom water-cooling loops

  • TypeLiquid Cooling System
  • Pre-bent 90-degree curve removes difficult manual bending
  • 16 mm outer diameter matches standard hard-tube fittings
  • Acrylic material provides clear coolant visibility
  • 110 mm and 415 mm straight sections allow custom trimming
  • Four tubes included for complete loop routing

Ready-to-install acrylic hard tubes

These pre-bent 90-degree acrylic tubes have a 16mm outer diameter and come in a pack of four. Each piece includes straight sections of 110mm and 415mm on either side of the bend. They are designed to simplify custom water-cooling builds for both beginners and experienced builders.

Check tubing compatibility and routing

Verify that your water-cooling components and fittings accept a 16mm outer diameter. Ensure your case layout can accommodate the fixed 110mm and 415mm straight lengths before the 90-degree bend. Plan the final cut points so each tube reaches its intended connection without tension.

Acrylic construction with fixed bend geometry

The transparent acrylic material provides a rigid, glossy finish that shows coolant colour clearly. Because the 90-degree curve is factory-formed, no heat gun or bending tool is required during assembly. You simply trim the straight ends to length, deburr the edges, and push the tubes onto compatible compression fittings.

Najważniejsze cechy

  • Pre-bent 90-degree curve removes difficult manual bending
  • 16 mm outer diameter matches standard hard-tube fittings
  • Acrylic material provides clear coolant visibility
  • 110 mm and 415 mm straight sections allow custom trimming
  • Four tubes included for complete loop routing

Specyfikacja

TypeLiquid Cooling System

Pytania dotyczące tego produktu

What is included in the box and do I need to buy fittings separately?

The box contains four pre-bent 90-degree acrylic hard tubes with an outer diameter of 16mm. Compression fittings for 16mm tubing must be purchased separately to complete the loop.

Should I choose a different tube size or bend angle for my build?

This pack only provides 16mm outer-diameter tubes with a fixed 90-degree bend. If your design requires a different diameter or angle, you will need another product.

How do the 110mm and 415mm straight sections affect my loop layout?

Each tube has a 90-degree curve with 110mm on one side and 415mm on the other. You can trim either straight section to fit the exact distance between components.

Także w tym dziale

Klienci porównywali też te produkty

Ten sam dział, ta sama kasa — osiem kryptowalut i 30-minutowa blokada kursu.