Akceptujemy kryptowaluty — posiadane środki można więc wykorzystać na zakup prawdziwego sprzętu.Płatność kryptowalutą — realny sprzęt w zamian. Bezpłatna, ubezpieczona dostawa na całym świecie powyżej 399 $. Neutralne kartony, bez oznaczeń, wysyłane z Niemiec.Bezpłatna, ubezpieczona dostawa powyżej 399 $. Kurs zostaje zablokowany na 30 minut od otwarcia kasy.Kurs zablokowany na 30 minut. Każdy produkt jest fabrycznie zapieczętowany, jego numer seryjny jest sprawdzany, a całość objęta jest 24-miesięczną gwarancją.Zapieczętowane fabrycznie, 24 miesiące gwarancji.

Obserwowane produkty Zaloguj się
Black M6 x 16mm rack screws and cage nuts with nylon washers in plastic can 50 sets

LORDWORLD

LORDWORLD M6 x 16mm Rack Screws & Cage Nuts 50 Sets Black

SKU CH-YS52-4HYW5

Fifty sets of M6 × 16 mm rack screws with pre-installed nylon washers and cage nuts for 19-inch cabinet mounting

  • High-quality carbon steel delivers solid, durable fastening
  • Philips truss-head with self-guiding pilot points speeds installation
  • Pre-installed nylon washers protect equipment from scratches
  • Zinc chromate plating resists rust for lasting finish
  • 50 sets per can cover standard 19-inch rack mounting

Rack Mounting Hardware Kit

The LORDWORLD kit supplies 50 sets of M6 screws and matching cage nuts for securing devices in standard 19-inch cabinets. Each set pairs a 16 mm Philips truss-head screw with a clip nut that seats in square mounting holes. The hardware is made from carbon steel with zinc chromate plating and ships in a single plastic can. It suits installers fitting servers, routers, shelves, blank panels, NAS units or amplifiers.

Capacity and Headroom

Fifty sets cover a full-height rack or multiple smaller enclosures without running short. The M6 by 16 mm screws reach through typical equipment ears and into the cage nuts with enough thread engagement for secure hold. Carbon steel construction and corrosion-resistant plating handle the weight of standard rack-mount gear. The quantity stops being sufficient only when a project demands more than fifty mounting points.

Build Integration

Pre-installed nylon washers protect equipment finishes from scratches during installation. Cage nuts snap into square holes on rack rails, eliminating the need for threaded rails or separate nut plates. The Philips drive works with common screwdrivers and the self-guiding pilot points speed alignment. No special tools or additional fasteners are required to complete a standard 19-inch mount.

Najważniejsze cechy

  • High-quality carbon steel delivers solid, durable fastening
  • Philips truss-head with self-guiding pilot points speeds installation
  • Pre-installed nylon washers protect equipment from scratches
  • Zinc chromate plating resists rust for lasting finish
  • 50 sets per can cover standard 19-inch rack mounting

Specyfikacja

BrandLORDWORLD

Pytania dotyczące tego produktu

Will the M6 x 16 mm screws fit the square-hole rails on my existing 19-inch rack?

Yes, the cage nuts are designed for square holes on standard 19-inch racks and cabinets, so they will mount directly onto your current rails.

How can I confirm the screws are seated correctly after installation?

The Philips truss-head with self-guiding pilot points drives flush, and the pre-installed nylon washers sit flat against the equipment, showing the fastener is fully tightened without scratching.

Does the 50-set can include both the screws and the cage nuts, or must I buy the nuts separately?

Each plastic can contains 50 complete sets — every set supplies one M6 x 16 mm screw with its nylon washer plus one matching cage nut, so nothing extra is required.

Także w tym dziale

Klienci porównywali też te produkty

Ten sam dział, ta sama kasa — osiem kryptowalut i 30-minutowa blokada kursu.