Akceptujemy kryptowaluty — posiadane środki można więc wykorzystać na zakup prawdziwego sprzętu.Płatność kryptowalutą — realny sprzęt w zamian. Bezpłatna, ubezpieczona dostawa na całym świecie powyżej 399 $. Neutralne kartony, bez oznaczeń, wysyłane z Niemiec.Bezpłatna, ubezpieczona dostawa powyżej 399 $. Kurs zostaje zablokowany na 30 minut od otwarcia kasy.Kurs zablokowany na 30 minut. Każdy produkt jest fabrycznie zapieczętowany, jego numer seryjny jest sprawdzany, a całość objęta jest 24-miesięczną gwarancją.Zapieczętowane fabrycznie, 24 miesiące gwarancji.

Obserwowane produkty Zaloguj się
Small black 30mm square case fan 30mm thick 2-pin connector no LED

Zyvpee

Zyvpee DFS301012M 30mm 12V 1.3W 2-Pin Case Fan

SKU CH-9VM2-AWKZ2

30 mm ball-bearing case fan runs on 12 V at 1.3 W with a 2-pin connector

  • TypeCase Fan
  • Fan Size30mm
  • Bearing TypeBall
  • Power Connector2 Pin
  • ColorBlack
  • LEDNon-LED
  • Compact 30 mm frame fits tight chassis spaces
  • Ball bearing ensures durable long-life operation
  • 12 V 1.3 W draw keeps power use low
  • Two-pin connector simplifies installation
  • Suits set-top boxes routers and hard-disk enclosures

Compact 30 mm case fan

The Zyvpee DFS301012M is a 30 mm square frame fan designed for tight enclosures such as set-top boxes, routers and hard-disk housings. It runs on 12 V and draws 1.3 W through a simple two-pin power connector. The ball-bearing motor and black non-LED housing keep the profile low at 30 by 10 mm. This fan suits builders who need targeted airflow in confined spaces.

Replacing louder sleeve-bearing units

The two-pin layout drops straight into legacy headers that lack PWM control, making the swap straightforward on older boards or embedded gear. Ball bearings reduce the rattle that develops in sleeve designs after extended heat cycles, so the upgrade is worth it when acoustic consistency matters more than variable speed. Buyers who need software fan curves or a three- or four-pin header will not find that control here.

Fits 30 mm mounting holes

The 30 mm hole pattern aligns with standard 3010 cut-outs, so no adapter brackets are required. Two wires keep cable routing simple in cramped chassis, and the 1.3 W draw leaves ample headroom on a shared 12 V rail. Because the unit has no integrated lighting or speed signal, it frees up header space for other monitored fans. Ensure the host device supplies a constant 12 V source, as no voltage regulator is onboard.

Najważniejsze cechy

  • Compact 30 mm frame fits tight chassis spaces
  • Ball bearing ensures durable long-life operation
  • 12 V 1.3 W draw keeps power use low
  • Two-pin connector simplifies installation
  • Suits set-top boxes routers and hard-disk enclosures

Specyfikacja

Brand3ccooler.com
SeriesDFS301012M
ModelDFS301012M
TypeCase Fan
Fan Size30mm
Bearing TypeBall
Power Connector2 Pin
ColorBlack
LEDNon-LED
Dimensions30*10mm

Pytania dotyczące tego produktu

Will this 30mm fan fit a 3010 mounting pattern?

Yes, the fan measures 30 by 10mm and matches the standard 3010 mounting holes used on set-top boxes, routers and hard-disk enclosures.

How do I connect the 2-pin plug, and what mistake should I avoid?

Plug the two wires onto a 12V DC header matching the polarity marked on the fan; the common error is reversing the positive and negative leads, which prevents the fan from spinning.

When will the ball bearing need replacement?

The ball bearing is rated for long life in continuous 12V operation; expect to replace the fan only if noise increases or airflow drops after extended use.

Także w tym dziale

Klienci porównywali też te produkty

Ten sam dział, ta sama kasa — osiem kryptowalut i 30-minutowa blokada kursu.