BFKK
BFKK 3U Rackmount Server Chassis EATX/ATX/MATX 4x5.25 6x3.5 Top/Side Cooling
- Rackmount
214,99 USD
0.00275801BTC
Skladom
NEMIX RAM
NEMIX RAM 32GB (2x16GB) DDR4 2133 CL15 260-Pin SODIMM memory upgrade
32 GB kit of two 16 GB DDR4 SODIMM modules running at 2133 MHz CL15 for POSIFLEX terminals
- Capacity32GB (2 x 16GB)
- SpeedDDR4 2133 (PC4 17000)
- ECCNo
- Buffered/RegisteredUnbuffered
- ChipsetMajor OEM Samsung, Micron, Hynix
- Voltage1.20V
- 32 GB kit doubles system memory for faster POS transactions
- DDR4 2133 CL15 timing keeps latency low in fanless terminals
- 2 V operation reduces heat inside sealed enclosures
- 260-pin SODIMM form factor fits the XT-6315E slot exactly
- Major-brand Samsung, Micron or Hynix ICs deliver enterprise-grade reliability
System-Specific DDR4 SODIMM Kit
This 32 GB kit contains two 16 GB modules built for the POSIFLEX XT-6315E JIVA high-end fanless POS terminal. It uses DDR4 2133 unbuffered non-ECC silicon from major OEM suppliers to match the platform's memory controller. The 260-pin form factor fits the terminal's SODIMM slots directly. Buyers who need ECC error correction or registered modules cannot use this kit.
Low-Voltage Operation
Each module runs at 1.20 V with CL15 timing at the rated 2133 MT/s speed. The absence of a heat spreader keeps the profile thin for the fanless chassis while the low voltage limits thermal output. Power draw stays modest under typical point-of-sale workloads. Builders who require higher-frequency memory or overclocking headroom should look elsewhere.
Dual-Rank 2Rx8 Layout
The 2Rx8 organisation populates both ranks per module for maximum density in two slots. Standard gold-edge 260-pin connectors ensure reliable seating during upgrades. No extra cables, brackets or software are required for installation. Systems that only accept single-rank SODIMMs or that need a 288-pin DIMM will not accept these modules.
Prednosti
- 32 GB kit doubles system memory for faster POS transactions
- DDR4 2133 CL15 timing keeps latency low in fanless terminals
- 2 V operation reduces heat inside sealed enclosures
- 260-pin SODIMM form factor fits the XT-6315E slot exactly
- Major-brand Samsung, Micron or Hynix ICs deliver enterprise-grade reliability
Špecifikácie
| Brand | NEMIX RAM |
|---|---|
| Series | POSIFLEX POS Series Point of Sale Kiosk Memory |
| Model | POSIFLEX POS DDR4 2133MHZ Non-ECC Unbuffered SODIMM |
| Part Number | MS17000-628K2 |
| Capacity | 32GB (2 x 16GB) |
| Speed | DDR4 2133 (PC4 17000) |
| ECC | No |
| Buffered/Registered | Unbuffered |
| Chipset | Major OEM Samsung, Micron, Hynix |
| Voltage | 1.20V |
| Compatible System | POSIFLEX POS |
| CAS Latency | CL15 |
| Heat Spreader | No |
| Type | 260-Pin DDR4 SODIMM |
| Rank | 2Rx8 |
| Features | DDR4 Non-ECC Unbuffered SODIMM Motherboard Compatible |
| Package Content | 32GB (2X16GB) DDR4 2133MHZ PC4-17000 2Rx8 1.2V CL15 260-PIN Non-ECC Unbuffered SODIMM KIT |
Otázky k tomuto produktu
How do I install these 260-pin SODIMM modules in the POSIFLEX XT-6315E terminal and what step is often missed?
Power off the terminal, remove the memory cover, align the notch on each 260-pin module with the slot key, press firmly until both side clips click, then replace the cover before powering on.
What maintenance or replacement will this 32GB DDR4 kit need over time?
No routine maintenance is required; the modules have no heat spreader and run at 1.20V, so replacement is only needed if a module fails or capacity must increase.
What limit appears first when the POS terminal runs sustained workloads with this CL15 memory?
The DDR4 2133 speed and CL15 latency set the bandwidth ceiling, so sustained throughput is limited by the 17000 MT/s transfer rate before thermal throttling occurs.
Aj v tomto oddelení
Zákazníci tiež porovnávali
Rovnaké oddelenie, rovnaká pokladňa — osem mien a kurz zablokovaný na 30 minút.
