Prijímame kryptomeny — takže mince, ktoré držíte, môžete zameniť za skutočný hardvér.Plaťte v krypte, miňte ho na skutočný hardvér. Poistená doprava zadarmo po celom svete nad 399 $. Neutrálne kartóny bez potlače, odosielané z Nemecka.Poistená doprava zadarmo nad 399 $. Váš kurz je zablokovaný na 30 minút hneď po otvorení pokladne.Kurz zablokovaný na 30 minút. Každý produkt je zapečatený, jeho sériové číslo je overené a vzťahuje sa naň 24-mesačná záruka.Zapečatené, 24-mesačná záruka.

Sledované položky Prihlásiť sa
Green circuit board with gold edge connector and mSATA slot for 1.8 inch MicroSATA conversion

SMUGDESK

SMUGDESK mSATA to MicroSATA 1.8" Adapter Card

SKU CH-DT08-X4ZPC

Converts an mSATA SSD to a 1.8 MicroSATA interface for legacy notebook and industrial equipment upgrades

  • Converts mSATA SSD to 1.8 MicroSATA host interface
  • Preserves original SATA read and write speed with no loss
  • Compact PCB fits small form factor chassis and embedded devices
  • Plug and play operation requires no driver installation
  • Cost effective upgrade for legacy notebooks and industrial equipment

mSATA to MicroSATA Adapter Card

This compact converter board lets you install a standard mSATA solid-state drive into a host device equipped with a 1.8-inch MicroSATA interface. It bridges the two connectors so the drive communicates over the native SATA pathway without signal degradation. No drivers or software are required, making it a straightforward hardware swap for compatible systems.

Suits legacy notebook repair and embedded upgrades

Technicians restoring older laptops, industrial controllers or POS terminals that only accept MicroSATA drives can use this adapter to fit readily available mSATA SSDs. The small PCB fits tight internal spaces and preserves the drive's original read and write performance. Builders whose host systems lack a MicroSATA connector or who require a different physical interface should consider other solutions.

Converts mSATA to 1.8-inch MicroSATA

The single deciding specification is the connector translation: the board accepts an mSATA module on one side and presents a 1.8-inch MicroSATA interface on the other. Only systems designed for that exact MicroSATA host interface can use this adapter; any other host connector will not mate with the board.

Prednosti

  • Converts mSATA SSD to 1.8 MicroSATA host interface
  • Preserves original SATA read and write speed with no loss
  • Compact PCB fits small form factor chassis and embedded devices
  • Plug and play operation requires no driver installation
  • Cost effective upgrade for legacy notebooks and industrial equipment

Špecifikácie

Pre tento produkt zatiaľ nie sú zverejnené žiadne špecifikácie.

Otázky k tomuto produktu

How do I install the mSATA SSD onto the adapter and connect it to the 1.8 MicroSATA host?

Insert the mSATA module into the converter board slot, secure it if a screw hole is present, then plug the board into the device's MicroSATA connector; no drivers are required.

Will the gold fingers or the mSATA slot wear out and need replacement after repeated swaps?

The adapter is a passive PCB with no moving parts; under normal use the gold fingers and slot do not require scheduled replacement.

Does the adapter limit the sequential speed of a fast mSATA SSD during long writes?

It preserves the native SATA read and write performance of the mSATA SSD with no obvious drop during continuous operation.

Aj v tomto oddelení

Zákazníci tiež porovnávali

Rovnaké oddelenie, rovnaká pokladňa — osem mien a kurz zablokovaný na 30 minút.