저희는 암호화폐로 결제를 받습니다 — 보유하신 코인으로 실제 하드웨어를 구매하실 수 있습니다.암호화폐로 결제하고, 실제 하드웨어 구매에 사용하십시오. 전 세계 어디서나 US$399 이상 구매 시 무료 보험 배송. 무지 상자에 담아 독일에서 발송합니다.US$399 이상 구매 시 무료 보험 배송. 체크아웃을 시작하면 30분 동안 환율이 잠깁니다.30분간 환율 잠금. 모든 제품은 밀봉된 상태로 일련번호를 확인한 후 24개월 보증을 제공합니다.밀봉 포장, 24개월 보증.

가격 추적 로그인
Green circuit board with gold edge connector and mSATA slot for 1.8 inch MicroSATA conversion

SMUGDESK

SMUGDESK mSATA to MicroSATA 1.8" Adapter Card

SKU CH-DT08-X4ZPC

Converts an mSATA SSD to a 1.8 MicroSATA interface for legacy notebook and industrial equipment upgrades

  • Converts mSATA SSD to 1.8 MicroSATA host interface
  • Preserves original SATA read and write speed with no loss
  • Compact PCB fits small form factor chassis and embedded devices
  • Plug and play operation requires no driver installation
  • Cost effective upgrade for legacy notebooks and industrial equipment

mSATA to MicroSATA Adapter Card

This compact converter board lets you install a standard mSATA solid-state drive into a host device equipped with a 1.8-inch MicroSATA interface. It bridges the two connectors so the drive communicates over the native SATA pathway without signal degradation. No drivers or software are required, making it a straightforward hardware swap for compatible systems.

Suits legacy notebook repair and embedded upgrades

Technicians restoring older laptops, industrial controllers or POS terminals that only accept MicroSATA drives can use this adapter to fit readily available mSATA SSDs. The small PCB fits tight internal spaces and preserves the drive's original read and write performance. Builders whose host systems lack a MicroSATA connector or who require a different physical interface should consider other solutions.

Converts mSATA to 1.8-inch MicroSATA

The single deciding specification is the connector translation: the board accepts an mSATA module on one side and presents a 1.8-inch MicroSATA interface on the other. Only systems designed for that exact MicroSATA host interface can use this adapter; any other host connector will not mate with the board.

주요 특징

  • Converts mSATA SSD to 1.8 MicroSATA host interface
  • Preserves original SATA read and write speed with no loss
  • Compact PCB fits small form factor chassis and embedded devices
  • Plug and play operation requires no driver installation
  • Cost effective upgrade for legacy notebooks and industrial equipment

사양

이 상품에 대해 아직 공개된 사양이 없습니다.

이 상품에 대한 질문

How do I install the mSATA SSD onto the adapter and connect it to the 1.8 MicroSATA host?

Insert the mSATA module into the converter board slot, secure it if a screw hole is present, then plug the board into the device's MicroSATA connector; no drivers are required.

Will the gold fingers or the mSATA slot wear out and need replacement after repeated swaps?

The adapter is a passive PCB with no moving parts; under normal use the gold fingers and slot do not require scheduled replacement.

Does the adapter limit the sequential speed of a fast mSATA SSD during long writes?

It preserves the native SATA read and write performance of the mSATA SSD with no obvious drop during continuous operation.

이 진열대의 다른 상품

고객들이 함께 비교한 상품

같은 진열대, 같은 체크아웃 — 코인 8종, 환율 잠금 30분.