Akceptujemy kryptowaluty — posiadane środki można więc wykorzystać na zakup prawdziwego sprzętu.Płatność kryptowalutą — realny sprzęt w zamian. Bezpłatna, ubezpieczona dostawa na całym świecie powyżej 399 $. Neutralne kartony, bez oznaczeń, wysyłane z Niemiec.Bezpłatna, ubezpieczona dostawa powyżej 399 $. Kurs zostaje zablokowany na 30 minut od otwarcia kasy.Kurs zablokowany na 30 minut. Każdy produkt jest fabrycznie zapieczętowany, jego numer seryjny jest sprawdzany, a całość objęta jest 24-miesięczną gwarancją.Zapieczętowane fabrycznie, 24 miesiące gwarancji.

Obserwowane produkty Zaloguj się
Green circuit board with gold edge connector and mSATA slot for 1.8 inch MicroSATA conversion

SMUGDESK

SMUGDESK mSATA to MicroSATA 1.8" Adapter Card

SKU CH-DT08-X4ZPC

Converts an mSATA SSD to a 1.8 MicroSATA interface for legacy notebook and industrial equipment upgrades

  • Converts mSATA SSD to 1.8 MicroSATA host interface
  • Preserves original SATA read and write speed with no loss
  • Compact PCB fits small form factor chassis and embedded devices
  • Plug and play operation requires no driver installation
  • Cost effective upgrade for legacy notebooks and industrial equipment

mSATA to MicroSATA Adapter Card

This compact converter board lets you install a standard mSATA solid-state drive into a host device equipped with a 1.8-inch MicroSATA interface. It bridges the two connectors so the drive communicates over the native SATA pathway without signal degradation. No drivers or software are required, making it a straightforward hardware swap for compatible systems.

Suits legacy notebook repair and embedded upgrades

Technicians restoring older laptops, industrial controllers or POS terminals that only accept MicroSATA drives can use this adapter to fit readily available mSATA SSDs. The small PCB fits tight internal spaces and preserves the drive's original read and write performance. Builders whose host systems lack a MicroSATA connector or who require a different physical interface should consider other solutions.

Converts mSATA to 1.8-inch MicroSATA

The single deciding specification is the connector translation: the board accepts an mSATA module on one side and presents a 1.8-inch MicroSATA interface on the other. Only systems designed for that exact MicroSATA host interface can use this adapter; any other host connector will not mate with the board.

Najważniejsze cechy

  • Converts mSATA SSD to 1.8 MicroSATA host interface
  • Preserves original SATA read and write speed with no loss
  • Compact PCB fits small form factor chassis and embedded devices
  • Plug and play operation requires no driver installation
  • Cost effective upgrade for legacy notebooks and industrial equipment

Specyfikacja

Na razie brak opublikowanej specyfikacji tego produktu.

Pytania dotyczące tego produktu

How do I install the mSATA SSD onto the adapter and connect it to the 1.8 MicroSATA host?

Insert the mSATA module into the converter board slot, secure it if a screw hole is present, then plug the board into the device's MicroSATA connector; no drivers are required.

Will the gold fingers or the mSATA slot wear out and need replacement after repeated swaps?

The adapter is a passive PCB with no moving parts; under normal use the gold fingers and slot do not require scheduled replacement.

Does the adapter limit the sequential speed of a fast mSATA SSD during long writes?

It preserves the native SATA read and write performance of the mSATA SSD with no obvious drop during continuous operation.

Także w tym dziale

Klienci porównywali też te produkty

Ten sam dział, ta sama kasa — osiem kryptowalut i 30-minutowa blokada kursu.