نقبل الدفع بالعملة المشفرة — لذلك يمكن للعملات الرقمية التي تملكها أن تشتري أجهزة حقيقية.ادفع بالعملة المشفرة، وأنفقها على أجهزة حقيقية. شحن مؤمن مجانا إلى كل أنحاء العالم لما يتجاوز 399 US$. صناديق شحن بسيطة بلا علامة تجارية، ترسل من ألمانيا.شحن مؤمن مجانا لما يتجاوز 399 US$. يُقفل سعرك لمدة 30 دقيقة بمجرد فتح صفحة الدفع.السعر مقفل لمدة 30 دقيقة. كل قطعة مختومة، ورقمها التسلسلي متحقق منه، ومشمولة بضمان 24 شهرا.مختوم، وبضمان 24 شهرا.

قائمة الرصد تسجيل الدخول
Four clear acrylic tubes bent at 90 degrees with 110mm and 415mm straight sections, 14mm outer diameter

Bitspower

Bitspower Pre-bent 90° Acrylic Hard Tube OD14mm 110x415mm 4-pack

SKU CH-YJ9R-3X8FY

Four pre-bent 90-degree acrylic tubes with 14 mm outer diameter and 110 mm by 415 mm straight sections simplify custom water-cooling builds

  • TypeLiquid Cooling System
  • Pre-bent 90° curve removes the need for manual tube bending
  • Acrylic hard tube construction provides rigid leak-resistant coolant paths
  • 14 mm outer diameter fits standard compression fittings
  • 110 mm and 415 mm straight sections allow custom trimming
  • Four tubes included to complete multiple loop runs

Pre-bent 90° acrylic tubes for custom loops

This four-pack of Bitspower pre-bent hard tubes gives builders ready-made 90-degree corners in clear acrylic. Each piece includes straight sections of 110mm and 415mm on either side of the bend. The tubes arrive at the outer diameter required for standard OD14mm fittings. Novices and experienced builders alike can skip the heating and bending step entirely.

Acrylic construction with OD14mm compatibility

The rigid acrylic material holds its shape without kinking and resists clouding over time. Because the 90-degree curves are factory-formed, alignment between components is more predictable than with hand-bent runs. Builders simply measure, cut the straight sections to length, and press the ends into their chosen OD14mm compression or push-fit fittings. No specialised bending tools or silicone inserts are needed.

Replaces hand-bent tubing in new builds

This set suits anyone assembling a custom water-cooling loop who wants to avoid the trial-and-error of bending acrylic themselves. It is not for builders who need curves other than 90 degrees or who prefer the flexibility of soft tubing. The fixed bend angle and straight-leg lengths determine the routing possibilities, so plan your component layout before committing.

أبرز المميزات

  • Pre-bent 90° curve removes the need for manual tube bending
  • Acrylic hard tube construction provides rigid leak-resistant coolant paths
  • 14 mm outer diameter fits standard compression fittings
  • 110 mm and 415 mm straight sections allow custom trimming
  • Four tubes included to complete multiple loop runs

المواصفات

TypeLiquid Cooling System

أسئلة حول هذا المنتج

What outer diameter does the 14 mm acrylic tube match for fittings?

The tube has a 14 mm outer diameter, so it fits standard 14 mm OD compression fittings used in custom loops.

How much straight length remains on each side of the 90° bend after the pre-bent curve?

Each piece provides 110 mm on one leg and 415 mm on the other, giving two distinct straight sections to trim to final size.

Do I need a heat gun to install these pre-bent tubes, or can I push them straight onto fittings?

No heat gun is required; simply cut the 110 mm and 415 mm legs to length, chamfer the ends, and press them into 14 mm OD fittings.

أيضًا في هذا القسم

عملاء قارنوا هذه المنتجات

نفس القسم، ونفس صفحة الدفع — ثماني عملات رقمية وقفل سعر لمدة 30 دقيقة.