Přijímáme kryptoměny — takže to, co držíte, můžete utratit za skutečný hardware.Plaťte kryptem, utrácejte ho za skutečný hardware. Pojištěná doprava zdarma po celém světě nad 399 $. Neutrální přepravní krabice bez loga, odesílané z Německa.Pojištěná doprava zdarma nad 399 $. Jakmile se otevře pokladna, je váš kurz zablokovaný na 30 minut.Kurz zablokovaný na 30 minut. Každý výrobek je zapečetěný, jeho sériové číslo je zkontrolované a vztahuje se na něj 24měsíční záruka.Zapečetěno, záruka 24 měsíců.

Sledované položky Přihlásit se
Green circuit board with black chips, gold edge connector, thin rectangular SODIMM module

NEMIX RAM

NEMIX RAM 16GB DDR4 2133 CL15 260-PIN SODIMM POSIFLEX RT-5015 memory upgrade

SKU CH-FB89-CR4RK

16GB DDR4 2133 CL15 SODIMM memory upgrade for POSIFLEX RT-5015 terminals

  • Capacity16GB
  • SpeedDDR4 2133 (PC4 17000)
  • ECCNo
  • Buffered/RegisteredUnbuffered
  • ChipsetMajor OEM Samsung, Micron, Hynix
  • Voltage1.20V
  • 16 GB capacity expands terminal multitasking headroom
  • DDR4 2133 speed matches POSIFLEX RT-5015 spec
  • CL15 latency keeps response tight under load
  • 2 V operation reduces power draw and heat
  • 260-pin SODIMM fits the terminal slot directly

POSIFLEX RT-5015 memory upgrade

This 16 GB DDR4 SODIMM is built for the POSIFLEX RT-5015 terminal. It targets IT teams and integrators who need a single-module capacity increase for point-of-sale or kiosk workloads. The 260-pin form factor matches the system slot exactly.

Thermals, noise and power

Operating at 1.20 V without a heat spreader, the module adds minimal thermal load to the compact chassis. Unbuffered, non-ECC silicon draws only the power required for the 2133 MT/s data rate. Passive cooling in the terminal is sufficient for continuous operation.

Deciding specification

The 2Rx8 rank organisation at CL15 latency is the detail that confirms compatibility with the RT-5015 memory controller. A different rank or timing will prevent the terminal from posting. Verify this exact configuration before ordering.

Přednosti

  • 16 GB capacity expands terminal multitasking headroom
  • DDR4 2133 speed matches POSIFLEX RT-5015 spec
  • CL15 latency keeps response tight under load
  • 2 V operation reduces power draw and heat
  • 260-pin SODIMM fits the terminal slot directly

Specifikace

BrandNEMIX RAM
SeriesPOSIFLEX POS Series Point of Sale Kiosk Memory
ModelPOSIFLEX POS DDR4 2133MHZ Non-ECC Unbuffered SODIMM
Part NumberMS17000-628K1
Capacity16GB
SpeedDDR4 2133 (PC4 17000)
ECCNo
Buffered/RegisteredUnbuffered
ChipsetMajor OEM Samsung, Micron, Hynix
Voltage1.20V
Compatible SystemPOSIFLEX POS
CAS LatencyCL15
Heat SpreaderNo
Type260-Pin DDR4 SODIMM
Rank2Rx8
FeaturesDDR4 Non-ECC Unbuffered SODIMM Motherboard Compatible
Package Content16GB (1X16GB) DDR4 2133MHZ PC4-17000 2Rx8 1.2V CL15 260-PIN Non-ECC Unbuffered SODIMM

Otázky k tomuto produktu

How do I install this 260-pin DDR4 SODIMM into the POSIFLEX RT-5015, and what step is often missed?

Power off the terminal and disconnect the power cord. Open the memory compartment, align the notch on the module with the slot key, insert at an angle, then press down firmly until both side clips click into place. The step often missed is verifying both clips have fully engaged.

What maintenance or replacement will this 16GB 1.20V module need over time?

No routine maintenance is required for this non-ECC unbuffered SODIMM. If a memory error appears later, the module would need replacement; otherwise it runs for the life of the terminal.

What limit appears first when this CL15 2133MHz memory runs under sustained load in the RT-5015?

The CAS latency of CL15 at 2133MHz sets the access timing ceiling. Under sustained workloads the memory controller reaches this latency bound before bandwidth or voltage limits become a factor.

Také v této kategorii

Zákazníci také porovnávali

Stejná kategorie, stejná pokladna — osm měn a kurz zamčený na 30 minut.