Timetec 32GB Kit (2×16GB) DDR4 2400 CL17 1.2V SODIMM for 2017 iMac 18,1/18,2/18,3
- 32GB (2 x 16GB)
- 260-Pin DDR4 SO-DIMM
Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.
Timetec
A 32 GB dual-channel DDR4 kit running at 3200 MHz with CL16 latency and a black aluminium heat spreader
Capacity 32GB (2 x 16GB)
This 32GB kit contains two 16GB DDR4 modules that run at 3200MHz with a tested latency of CL16-18-18-38. The black aluminum heat spreader helps manage thermals during extended sessions. It is built for desktop gaming and enthusiast systems that use DDR4 memory.
Each IC is individually screened to maintain stability at the rated 3200MHz speed and 1.35V voltage. The dual-rank 1Rx8 organisation supports consistent bandwidth under prolonged workloads. Enabling the XMP2.0 profile in the BIOS is required to reach the advertised frequency; otherwise the modules operate at the 2400MHz base speed.
The DDR4 288-pin unbuffered non-ECC standard used here tops out at the PC4-25600 data rate of 25,600MB/s. Higher frequencies or tighter timings would require a different memory generation. Compatibility depends on the motherboard's qualified vendor list for DDR4 3200MHz operation.
| Capacity | 32GB (2 x 16GB) |
|---|---|
| Speed | DDR4 3200 (PC4 25600) |
| Color | Black |
Tämän mallin muut versiot
Sama tuoteperhe, eri muisti, jäähdytin tai kellotaajuus — vertaile ennen päätöstä.
The modules run at 1.35 V with a black aluminum heat spreader to dissipate heat, and they are rated for continuous operation at the advertised 3200 MHz CL16-18-18-38 timings once XMP 2.0 is enabled in the BIOS.
Your motherboard must support Intel XMP 2.0 (or the AMD equivalent) and you must enable the profile in the BIOS; without it the kit will run at the base 2400 MHz speed.
Yes, the kit uses standard 288-pin DDR4 unbuffered non-ECC modules at 1.35 V and is validated for both Intel and AMD DDR4 platforms, so it will install in any compatible DDR4 motherboard.
Myös tällä osastolla
Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.
Valuutta, jolla maksetaan, sekä valuutta, jossa hinnat näytetään.
Lähetetään lompakostasi kassalla
Vain näyttöä varten — hinnat ovat Yhdysvaltain dollareissa
Valuuttaa ei löytynyt.
Valitse kieli, jolla sivusto puhuu sinulle.
Ei vastaavaa kieltä.
Uusi täällä?
Onko sinulla jo tili?
Automaattista palautusta ei ole: kauppa ei lähetä sähköpostia lainkaan, joten kertakäyttöistä linkkiä ei ole mistä pyytää. Jätä osoite tilille, niin se käsitellään käsin.
Pyyntö kirjattu
Mikään ei ole tulossa sähköpostiisi — tämä kauppa ei lähetä sähköpostia lainkaan. Joku käsittelee nämä pyynnöt käsin.
Muistitko sen?