SanDisk
SanDisk Cruzer Blade 8 GB USB 2.0 USB flash drive Black SDCZ50-008G-B35
391,99 $US
0.00500958BTC
En stock
Computer Memory Solutions
Computer Memory Solutions 8GB (2x4GB) DDR3 1333 ECC memory upgrade
ECC DDR3 1333 MHz kit adds 8 GB across two unregistered DIMMs for Supermicro X9SCL boards
- Capacity8GB (2 x 4GB)
- Type240-Pin DDR3 SDRAM
- SpeedDDR3 1333 (PC3 10600)
- CAS LatencyCL9
- Timing9-9-9
- Voltage1.5V
- ECC protection guards data integrity on critical workloads
- 1333 MHz DDR3 speed matches the board specification
- 240-pin unregistered DIMMs install directly in four slots
- 8 GB kit (2×4 GB) leaves room to reach 32 GB
- Tested compatible with Supermicro X9SCL series motherboards
Targeted ECC upgrade for Supermicro X9SCL
This 8 GB kit contains two 4 GB DDR3 ECC unregistered DIMMs validated for the Supermicro MBD-X9SCL-0, MBD-X9SCL-F-B and MBD-X9SCL-B boards. It serves administrators who need to populate empty slots or replace failed modules in those specific platforms without guesswork. Builders using other motherboards should verify their own qualified-vendor lists before purchasing.
Thermals noise and power in normal use
Each module operates at the standard 1.5 V DDR3 voltage with no heat spreader, relying on chassis airflow for cooling. The low-profile design adds no acoustic load and draws only the power defined by the JEDEC DDR3-1333 specification during typical server workloads.
Build quality and daily connectors
The 240-pin DIMMs use major-brand chips and a 2Rx8 organisation, fitting the four memory sockets on the target boards up to the 32 GB maximum. Installation follows the standard vertical DIMM slot procedure; no extra cables, brackets or software configuration are required beyond normal BIOS memory detection.
Points forts
- ECC protection guards data integrity on critical workloads
- 1333 MHz DDR3 speed matches the board specification
- 240-pin unregistered DIMMs install directly in four slots
- 8 GB kit (2×4 GB) leaves room to reach 32 GB
- Tested compatible with Supermicro X9SCL series motherboards
Caractéristiques
| Brand | Computer Memory Solutions |
|---|---|
| Model | CM5127210600ECCNRH2R8 |
| Capacity | 8GB (2 x 4GB) |
| Type | 240-Pin DDR3 SDRAM |
| Speed | DDR3 1333 (PC3 10600) |
| CAS Latency | CL9 |
| Timing | 9-9-9 |
| Voltage | 1.5V |
| ECC | Yes |
| Buffered/Registered | Unregistered |
| Rank | 2Rx8 |
| Chipset | Major Brand Chipset |
| Heat Spreader | No |
| Compatible System | SUPERMICRO MBD-X9SCL-0, MBD-X9SCL-F-B, MBD-X9SCL-B |
| Package Content | 2 Memory RAM Sticks |
Questions sur cet article
How do I install the 240-pin DDR3 ECC modules into the four slots on my Supermicro X9SCL board, and what step is often missed?
Align the notch on each 240-pin DDR3 stick with the slot key, press down firmly until both side clips click, then verify in BIOS that all 8 GB are detected at 1333 MHz; the step often missed is seating both ends evenly so the clips engage fully.
What maintenance or replacement will the unregistered ECC kit need over its service life?
The modules have no heat spreaders and carry a limited lifetime warranty against manufacturing defects; no scheduled maintenance is required, and replacement would only occur if a stick fails the warranty exchange.
What limit appears first when the 1.5 V DDR3 1333 kit runs sustained workloads on the X9SCL platform?
The platform caps total memory at 32 GB across its four sockets, so the 8 GB kit itself will not hit a capacity ceiling, but the board’s 32 GB maximum is the first hard limit you would reach when expanding.
Également dans ce rayon
Les clients ont aussi comparé
Même rayon, même caisse — huit monnaies et un taux bloqué 30 minutes.
SAMSUNG
SAMSUNG M393A1K43DB2-CWE DDR4-3200 8GB ECC Registered server RAM
74,99 $US
0.00095836BTC
En stock