NEMIX RAM
NEMIX RAM 576GB 6x96GB DDR5 6400 CL52 1.1V ECC RDIMM Supermicro H14DSG-O-CPU memory upgrade
576GB DDR5 6400 CL52 1.1V ECC RDIMM kit for Supermicro H14DSG-O-CPU servers
- Capacity576GB (6 x 96GB)
- Type288-Pin DDR5 RDIMM
- SpeedDDR5 6400 (PC5 51200)
- CAS LatencyCL52
- Voltage1.10V
- ECCYes
- 576 GB total capacity from six 96 GB modules
- DDR5-6400 speed with CL52 latency at 1.1 V
- Registered ECC design for error correction and full-slot stability
- 288-pin RDIMM form factor matched to Supermicro H14DSG-O-CPU
- Built with major OEM chips from Samsung, Micron or Hynix
576GB DDR5-6400 ECC RDIMM kit
This 576GB kit contains six 96GB DDR5-6400 Registered ECC RDIMMs built for the Supermicro H14DSG-O-CPU motherboard. Each module runs at 1.1V with CL52 latency and a 2Rx4 organisation, matching the board's memory controller expectations for full-capacity recognition and rated-speed operation.
Suits servers needing maximum registered ECC
The Registered (buffered) architecture offloads the memory controller so all slots stay stable when fully populated, while ECC corrects single-bit errors on the fly. This kit is not for systems that require unbuffered UDIMMs, SODIMM form factors, non-ECC memory, or lower-density modules that the board's population rules do not support.
576GB total across six 96GB DIMMs
The kit fills six slots with 96GB each, delivering the full 576GB at DDR5-6400 (PC5-51200). Capacity headroom ends when the motherboard's maximum supported memory per slot or total population limit is reached; consult the system manual for exact population order and approved configurations before installation.
Points forts
- 576 GB total capacity from six 96 GB modules
- DDR5-6400 speed with CL52 latency at 1.1 V
- Registered ECC design for error correction and full-slot stability
- 288-pin RDIMM form factor matched to Supermicro H14DSG-O-CPU
- Built with major OEM chips from Samsung, Micron or Hynix
Caractéristiques
| Brand | NEMIX RAM |
|---|---|
| Series | NEMIX RAM Original Series Server Memory |
| Model | DDR5 ECC RDIMM Registered Server Memory |
| Part Number | MR51200-9624K6 |
| Capacity | 576GB (6 x 96GB) |
| Type | 288-Pin DDR5 RDIMM |
| Speed | DDR5 6400 (PC5 51200) |
| CAS Latency | CL52 |
| Voltage | 1.10V |
| ECC | Yes |
| Buffered/Registered | Registered |
| Rank | 2Rx4 |
| Chipset | Major OEM Samsung, Micron, Hynix |
| Heat Spreader | No |
| Compatible System | Supermicro |
| Features | DDR5 ECC RDIMM Motherboard Compatible |
| Package Content | 576GB 6X96GB DDR5 6400MHz PC5-51200 2Rx4 1.1V 288-PIN ECC RDIMM KIT |
Questions sur cet article
My Supermicro H14DSG-O-CPU motherboard only has 8 DDR5 slots — will this 6-module 576 GB kit leave room for future expansion?
Yes, the kit uses six 288-pin RDIMM modules, leaving two slots free on an 8-slot board. Follow the manual's population order to keep all channels balanced and allow adding matched modules later.
Can I mix these 6400 CL52 1.1 V RDIMMs with slower DDR5 ECC modules already installed in my server?
The board will downclock every module to the slowest speed and loosest latency present. For stable operation at the rated 6400 MT/s and CL52, populate all channels with identical 1.1 V registered DIMMs.
After installing the 6x96 GB kit, how can I verify the server sees the full 576 GB at DDR5-6400 with ECC active?
Check the BIOS memory information screen or run dmidecode / lshw on Linux; both will show 576 GB total, 6400 MT/s data rate, registered ECC type, and 1.1 V operating voltage.
Également dans ce rayon
Les clients ont aussi comparé
Même rayon, même caisse — huit monnaies et un taux bloqué 30 minutes.
Mushkin Enhanced 4GB DDR2-800 CL6 SoDIMM Apple 971741A memory upgrade
SK hynix HYMD232M646C6-J 256MB DDR 333MHz PC2700 CL2.5 SODIMM laptop RAM
- 4GB (2 x 2GB)



