暗号資産でのお支払いに対応—お手持ちのコインで、本物のハードウェアをご購入いただけます。暗号資産で支払い、本物のハードウェアに使う。 $399以上のご注文で、世界中どこでも送料無料（保険付き）。無地・ノーブランドの外箱で、ドイツから発送いたします。$399以上で送料無料（保険付き）。 注文手続きを開始すると、レートは30分間ロックされます。レートは30分間ロック。 すべての商品は未開封で、シリアル番号を確認した上で、24か月保証が付いています。未開封、24か月保証。

ウォッチリスト ログイン
Transparent ABS housing for Raspberry Pi Camera Module 3, open back for cable, tripod mount underneath

MCDODO

MCDODO ABS Housing for Raspberry Pi Camera Module 3 IMX519 16MP

SKU CH-VNK4-CCSG5

ABS housing protects Raspberry Pi Camera Module 3, V1, V2 and any 25×24 mm board, includes screws and tripod mount

  • TypeSingle Board Computers
  • Protects the IMX519 16MP camera with rigid ABS plastic
  • Fits Raspberry Pi Camera Module 3, V1, V2 and any 25 * 24mm board
  • Secures in seconds using four included screws and snap-fit cover
  • Weighs only 9g at 1.57 * 1.37 * .58 inch for pocket carry
  • Mounts on standard 1/4-20 tripod with cable opening at rear

Protective ABS housing for Camera Module 3

This transparent case fits the official Raspberry Pi Camera Module 3 with IMX519 16MP autofocus sensor. It also accepts Camera Module V1, V2 and any other 25 by 24 millimetre camera board. The rigid ABS plastic shields the board from dust and knocks while keeping the lens area clear.

Limited to boards measuring 25 by 24 millimetres

The internal cavity matches that exact footprint so larger or smaller modules will not seat correctly. No mounting points exist for other form factors and the cable opening is sized for the standard flat ribbon used by the supported modules.

Tool-free assembly with four included screws

Fasten the board using the supplied screws then snap the top cover onto the base. The back cut-out lets you disconnect the ribbon cable without reopening the case. A standard quarter-twenty tripod thread is moulded into the base for fixed positioning.

特長

  • Protects the IMX519 16MP camera with rigid ABS plastic
  • Fits Raspberry Pi Camera Module 3, V1, V2 and any 25 * 24mm board
  • Secures in seconds using four included screws and snap-fit cover
  • Weighs only 9g at 1.57 * 1.37 * .58 inch for pocket carry
  • Mounts on standard 1/4-20 tripod with cable opening at rear

仕様

TypeSingle Board Computers

この商品に関する質問

Which Raspberry Pi camera boards fit this 25 * 24mm ABS housing?

The case accepts the official Raspberry Pi Camera Module 3 with IMX519 16MP autofocus sensor as well as V1 and V2 modules and any board measuring 25 * 24mm.

How does the 16MP IMX519 sensor benefit my project inside this enclosure?

The 16MP autofocus camera captures high-resolution stills and video while the transparent ABS cover protects the lens without blocking the field of view.

What does the 1/4-20 mounting hole allow me to do with the housed camera?

The standard 1/4-20 thread lets you attach the enclosure to any compatible tripod or mount for fixed-position imaging.

同じ売り場の商品

よく比較されている商品

同じ売り場、同じレジ — 8種類のコインと30分間のレートロック。