저희는 암호화폐로 결제를 받습니다 — 보유하신 코인으로 실제 하드웨어를 구매하실 수 있습니다.암호화폐로 결제하고, 실제 하드웨어 구매에 사용하십시오. 전 세계 어디서나 US$399 이상 구매 시 무료 보험 배송. 무지 상자에 담아 독일에서 발송합니다.US$399 이상 구매 시 무료 보험 배송. 체크아웃을 시작하면 30분 동안 환율이 잠깁니다.30분간 환율 잠금. 모든 제품은 밀봉된 상태로 일련번호를 확인한 후 24개월 보증을 제공합니다.밀봉 포장, 24개월 보증.

가격 추적 로그인
Transparent ABS housing for Raspberry Pi Camera Module 3, open back for cable, tripod mount underneath

MCDODO

MCDODO ABS Housing for Raspberry Pi Camera Module 3 IMX519 16MP

SKU CH-VNK4-CCSG5

ABS housing protects Raspberry Pi Camera Module 3, V1, V2 and any 25×24 mm board, includes screws and tripod mount

  • TypeSingle Board Computers
  • Protects the IMX519 16MP camera with rigid ABS plastic
  • Fits Raspberry Pi Camera Module 3, V1, V2 and any 25 * 24mm board
  • Secures in seconds using four included screws and snap-fit cover
  • Weighs only 9g at 1.57 * 1.37 * .58 inch for pocket carry
  • Mounts on standard 1/4-20 tripod with cable opening at rear

Protective ABS housing for Camera Module 3

This transparent case fits the official Raspberry Pi Camera Module 3 with IMX519 16MP autofocus sensor. It also accepts Camera Module V1, V2 and any other 25 by 24 millimetre camera board. The rigid ABS plastic shields the board from dust and knocks while keeping the lens area clear.

Limited to boards measuring 25 by 24 millimetres

The internal cavity matches that exact footprint so larger or smaller modules will not seat correctly. No mounting points exist for other form factors and the cable opening is sized for the standard flat ribbon used by the supported modules.

Tool-free assembly with four included screws

Fasten the board using the supplied screws then snap the top cover onto the base. The back cut-out lets you disconnect the ribbon cable without reopening the case. A standard quarter-twenty tripod thread is moulded into the base for fixed positioning.

주요 특징

  • Protects the IMX519 16MP camera with rigid ABS plastic
  • Fits Raspberry Pi Camera Module 3, V1, V2 and any 25 * 24mm board
  • Secures in seconds using four included screws and snap-fit cover
  • Weighs only 9g at 1.57 * 1.37 * .58 inch for pocket carry
  • Mounts on standard 1/4-20 tripod with cable opening at rear

사양

TypeSingle Board Computers

이 상품에 대한 질문

Which Raspberry Pi camera boards fit this 25 * 24mm ABS housing?

The case accepts the official Raspberry Pi Camera Module 3 with IMX519 16MP autofocus sensor as well as V1 and V2 modules and any board measuring 25 * 24mm.

How does the 16MP IMX519 sensor benefit my project inside this enclosure?

The 16MP autofocus camera captures high-resolution stills and video while the transparent ABS cover protects the lens without blocking the field of view.

What does the 1/4-20 mounting hole allow me to do with the housed camera?

The standard 1/4-20 thread lets you attach the enclosure to any compatible tripod or mount for fixed-position imaging.

이 진열대의 다른 상품

고객들이 함께 비교한 상품

같은 진열대, 같은 체크아웃 — 코인 8종, 환율 잠금 30분.