暗号資産でのお支払いに対応—お手持ちのコインで、本物のハードウェアをご購入いただけます。暗号資産で支払い、本物のハードウェアに使う。 $399以上のご注文で、世界中どこでも送料無料（保険付き）。無地・ノーブランドの外箱で、ドイツから発送いたします。$399以上で送料無料（保険付き）。 注文手続きを開始すると、レートは30分間ロックされます。レートは30分間ロック。 すべての商品は未開封で、シリアル番号を確認した上で、24か月保証が付いています。未開封、24か月保証。

ウォッチリスト ログイン
Green circuit board with black memory chips, no heat spreader, 288 gold pins along bottom edge

NEMIX RAM

NEMIX RAM 8GB DDR5 5600 CL46 1Rx8 1.1V UDIMM Supermicro X13SAW-F memory upgrade

SKU CH-XNJC-DXKGS

8GB DDR5 5600 CL46 1Rx8 1.1V UDIMM built with major OEM chips and validated for the Supermicro X13SAW-F motherboard

  • Capacity8GB
  • Type288-Pin DDR5 UDIMM
  • SpeedDDR5 5600 (PC5 44800)
  • CAS LatencyCL46
  • Voltage1.10V
  • ECCNo

Size 8GB

  • Precise DDR5-5600 timing matches your controller for full-speed operation
  • 288-pin UDIMM form factor fits the Supermicro X13SAW-F board exactly
  • Major OEM chips from Samsung, Micron, or Hynix tested at rated speed and voltage
  • 1V CL46 1Rx8 Non-ECC spec meets the motherboard's memory population rules
  • Lifetime replacement warranty and free US-based technical support included

8GB DDR5-5600 UDIMM for Supermicro X13SAW-F

This 8GB DDR5 module is an exact-match upgrade for the Supermicro X13SAW-F motherboard. It runs at 5600 MT/s with CL46 latency at 1.10V. The 1Rx8 unbuffered non-ECC design matches the board's memory controller expectations. Major OEM chips from Samsung Micron or Hynix provide tested stability.

Suitable and unsuitable use cases

This kit suits owners of the Supermicro X13SAW-F who need a single 8GB DDR5 DIMM to fill a slot or replace a module. It is not for systems that require ECC registered memory or SODIMM form factors. Builders needing higher capacity per slot or registered server memory should look elsewhere.

DDR5-5600 CL46 1.10V 1Rx8 specification

The decisive specification is the DDR5-5600 CL46 1.10V 1Rx8 unbuffered non-ECC profile. Your motherboard must support this exact speed timing voltage and rank configuration for the module to be recognized at full capacity and rated speed. Consult the board manual for approved population rules before purchase.

特長

  • Precise DDR5-5600 timing matches your controller for full-speed operation
  • 288-pin UDIMM form factor fits the Supermicro X13SAW-F board exactly
  • Major OEM chips from Samsung, Micron, or Hynix tested at rated speed and voltage
  • 1V CL46 1Rx8 Non-ECC spec meets the motherboard's memory population rules
  • Lifetime replacement warranty and free US-based technical support included

仕様

BrandNEMIX RAM
SeriesNEMIX RAM Original Series Memory
ModelDDR5 Non-ECC Unbuffered UDIMM Memory
Part NumberMD44800-818K1
Capacity8GB
Type288-Pin DDR5 UDIMM
SpeedDDR5 5600 (PC5 44800)
CAS LatencyCL46
Voltage1.10V
ECCNo
Buffered/RegisteredUnbuffered
Rank1Rx8
ChipsetMajor OEM Samsung, Micron, Hynix
Heat SpreaderNo
Compatible SystemSupermicro
FeaturesDDR5 Non-ECC Unbuffered UDIMM Motherboard Compatible
Package Content8GB DDR5 5600MHz PC5-44800 1Rx8 1.1V 288-PIN Non-ECC UDIMM KIT

このモデルの他のバージョン

同シリーズにさらに 5点

同じファミリーで、メモリ・クーラー・クロックが異なります — 購入前に比較してください。

この商品に関する質問

Will the 5600MHz DDR5 speed run at full frequency on my Supermicro X13SAW-F board?

The module is spec-matched to the X13SAW-F memory controller, so it will be recognised at full capacity and operate at its rated DDR5 5600 speed with CL46 timing.

Is the 288-pin PC5-44800 interface the exact DDR5 UDIMM standard this motherboard requires?

Yes, it is a 288-pin DDR5 unbuffered UDIMM built to the PC5-44800 standard, matching the board's required form factor and data rate.

Does the 1Rx8 single-rank layout fit the X13SAW-F DIMM slots without clearance issues?

The single-rank 1Rx8 design uses standard-height chips with no heat spreader, so it seats cleanly in the board's 288-pin UDIMM slots.

同じ売り場の商品

よく比較されている商品

同じ売り場、同じレジ — 8種類のコインと30分間のレートロック。