저희는 암호화폐로 결제를 받습니다 — 보유하신 코인으로 실제 하드웨어를 구매하실 수 있습니다.암호화폐로 결제하고, 실제 하드웨어 구매에 사용하십시오. 전 세계 어디서나 US$399 이상 구매 시 무료 보험 배송. 무지 상자에 담아 독일에서 발송합니다.US$399 이상 구매 시 무료 보험 배송. 체크아웃을 시작하면 30분 동안 환율이 잠깁니다.30분간 환율 잠금. 모든 제품은 밀봉된 상태로 일련번호를 확인한 후 24개월 보증을 제공합니다.밀봉 포장, 24개월 보증.

가격 추적 로그인
Green circuit board with black memory chips, no heat spreader, 288 gold pins along bottom edge

NEMIX RAM

NEMIX RAM 8GB DDR5 5600 CL46 1Rx8 1.1V UDIMM Supermicro X13SAW-F memory upgrade

SKU CH-XNJC-DXKGS

8GB DDR5 5600 CL46 1Rx8 1.1V UDIMM built with major OEM chips and validated for the Supermicro X13SAW-F motherboard

  • Capacity8GB
  • Type288-Pin DDR5 UDIMM
  • SpeedDDR5 5600 (PC5 44800)
  • CAS LatencyCL46
  • Voltage1.10V
  • ECCNo

Size 8GB

  • Precise DDR5-5600 timing matches your controller for full-speed operation
  • 288-pin UDIMM form factor fits the Supermicro X13SAW-F board exactly
  • Major OEM chips from Samsung, Micron, or Hynix tested at rated speed and voltage
  • 1V CL46 1Rx8 Non-ECC spec meets the motherboard's memory population rules
  • Lifetime replacement warranty and free US-based technical support included

8GB DDR5-5600 UDIMM for Supermicro X13SAW-F

This 8GB DDR5 module is an exact-match upgrade for the Supermicro X13SAW-F motherboard. It runs at 5600 MT/s with CL46 latency at 1.10V. The 1Rx8 unbuffered non-ECC design matches the board's memory controller expectations. Major OEM chips from Samsung Micron or Hynix provide tested stability.

Suitable and unsuitable use cases

This kit suits owners of the Supermicro X13SAW-F who need a single 8GB DDR5 DIMM to fill a slot or replace a module. It is not for systems that require ECC registered memory or SODIMM form factors. Builders needing higher capacity per slot or registered server memory should look elsewhere.

DDR5-5600 CL46 1.10V 1Rx8 specification

The decisive specification is the DDR5-5600 CL46 1.10V 1Rx8 unbuffered non-ECC profile. Your motherboard must support this exact speed timing voltage and rank configuration for the module to be recognized at full capacity and rated speed. Consult the board manual for approved population rules before purchase.

주요 특징

  • Precise DDR5-5600 timing matches your controller for full-speed operation
  • 288-pin UDIMM form factor fits the Supermicro X13SAW-F board exactly
  • Major OEM chips from Samsung, Micron, or Hynix tested at rated speed and voltage
  • 1V CL46 1Rx8 Non-ECC spec meets the motherboard's memory population rules
  • Lifetime replacement warranty and free US-based technical support included

사양

BrandNEMIX RAM
SeriesNEMIX RAM Original Series Memory
ModelDDR5 Non-ECC Unbuffered UDIMM Memory
Part NumberMD44800-818K1
Capacity8GB
Type288-Pin DDR5 UDIMM
SpeedDDR5 5600 (PC5 44800)
CAS LatencyCL46
Voltage1.10V
ECCNo
Buffered/RegisteredUnbuffered
Rank1Rx8
ChipsetMajor OEM Samsung, Micron, Hynix
Heat SpreaderNo
Compatible SystemSupermicro
FeaturesDDR5 Non-ECC Unbuffered UDIMM Motherboard Compatible
Package Content8GB DDR5 5600MHz PC5-44800 1Rx8 1.1V 288-PIN Non-ECC UDIMM KIT

이 모델의 다른 버전

같은 라인업에서 5개 더

같은 제품군에서 메모리·쿨러·클럭이 다릅니다 — 결정 전에 비교해 보세요.

이 상품에 대한 질문

Will the 5600MHz DDR5 speed run at full frequency on my Supermicro X13SAW-F board?

The module is spec-matched to the X13SAW-F memory controller, so it will be recognised at full capacity and operate at its rated DDR5 5600 speed with CL46 timing.

Is the 288-pin PC5-44800 interface the exact DDR5 UDIMM standard this motherboard requires?

Yes, it is a 288-pin DDR5 unbuffered UDIMM built to the PC5-44800 standard, matching the board's required form factor and data rate.

Does the 1Rx8 single-rank layout fit the X13SAW-F DIMM slots without clearance issues?

The single-rank 1Rx8 design uses standard-height chips with no heat spreader, so it seats cleanly in the board's 288-pin UDIMM slots.

이 진열대의 다른 상품

고객들이 함께 비교한 상품

같은 진열대, 같은 체크아웃 — 코인 8종, 환율 잠금 30분.