暗号資産でのお支払いに対応—お手持ちのコインで、本物のハードウェアをご購入いただけます。暗号資産で支払い、本物のハードウェアに使う。 $399以上のご注文で、世界中どこでも送料無料（保険付き）。無地・ノーブランドの外箱で、ドイツから発送いたします。$399以上で送料無料（保険付き）。 注文手続きを開始すると、レートは30分間ロックされます。レートは30分間ロック。 すべての商品は未開封で、シリアル番号を確認した上で、24か月保証が付いています。未開封、24か月保証。

ウォッチリスト ログイン
Four black DDR2 UDIMM modules in a kit

OWC

OWC 4GB (4x1GB) DDR2 533 PC2-4200 CL4 1.8V Non-ECC UDIMM Kit

SKU CH-N3A3-ADBP3

Four 1 GB DDR2 533 modules run at CL4 latency and 1.8 V for desktop upgrades

  • Capacity4GB (4 x 1GB)
  • SpeedDDR2 533 (PC2 4200)
  • CAS LatencyCL4
  • Voltage1.8V
  • ECCNo
  • Buffered/RegisteredUnbuffered

Capacity 4GB (4 x 1GB)

  • 4GB total capacity from four 1GB modules
  • DDR2 533 speed with CL4 latency for responsive operation
  • 8V JEDEC standard voltage ensures broad desktop compatibility
  • Unbuffered non-ECC design suited for consumer desktop boards
  • 240-pin UDIMM form factor fits standard DDR2 slots

OWC DDR2 533 4GB Kit

This OWC kit provides four 1 GB DDR2 533 modules for a total of 4 GB. It is built as an unbuffered non-ECC upgrade for desktop systems that accept 240-pin DIMMs. Each module runs at the standard 1.8 V JEDEC voltage and carries a CL4 latency rating. The kit targets users who need a straightforward capacity increase on older platforms.

Sustained load behaviour

JEDEC-compliant DDR2 533 modules maintain their rated 533 MT/s data rate and CL4 timing during extended use because they operate at the specified 1.8 V without overclocking. The unbuffered design adds no extra register delay, so latency stays consistent across long sessions. ROHS-compliant components and OWC in-house validation reduce the risk of thermal throttling or errors over time.

Deciding specification

The critical figure is the DDR2 533 (PC2-4200) speed rating combined with the 240-pin form factor. A motherboard must explicitly support DDR2 533 unbuffered non-ECC DIMMs at 1.8 V for these modules to function. If the board requires a different DDR generation, a higher voltage, or registered memory, this kit will not be compatible.

特長

  • 4GB total capacity from four 1GB modules
  • DDR2 533 speed with CL4 latency for responsive operation
  • 8V JEDEC standard voltage ensures broad desktop compatibility
  • Unbuffered non-ECC design suited for consumer desktop boards
  • 240-pin UDIMM form factor fits standard DDR2 slots

仕様

BrandOWC
Part Number4U2D21R8004S
Capacity4GB (4 x 1GB)
SpeedDDR2 533 (PC2 4200)
CAS LatencyCL4
Voltage1.8V
ECCNo
Buffered/RegisteredUnbuffered
Multi-channel KitDual Channel Kit
ColorBlack
Heat SpreaderNo
Recommend UseDesktops
LED ColorNone

このモデルの他のバージョン

同シリーズにさらに 4点

同じファミリーで、メモリ・クーラー・クロックが異なります — 購入前に比較してください。

この商品に関する質問

How much heat will the four 1.8 V DDR2 modules generate during continuous all-day use?

Each module runs at the standard 1.8 V JEDEC voltage for DDR2 533, so heat output is typical for unbuffered desktop DIMMs; the kit has no heat spreaders, so case airflow is the main cooling path.

What must the desktop already provide to accept this 240-pin UDIMM kit?

The system needs four free 240-pin DDR2 slots that support 1.8 V unbuffered non-ECC memory and dual-channel operation for the matched 4 x 1 GB configuration.

Will the CL4 533 MHz sticks down-clock automatically if the motherboard only supports slower DDR2 speeds?

Yes — JEDEC-compliant DDR2 modules negotiate the highest common speed with the memory controller, so they will run at the board's maximum supported rate without manual setup.

同じ売り場の商品

よく比較されている商品

同じ売り場、同じレジ — 8種類のコインと30分間のレートロック。