暗号資産でのお支払いに対応—お手持ちのコインで、本物のハードウェアをご購入いただけます。暗号資産で支払い、本物のハードウェアに使う。 $399以上のご注文で、世界中どこでも送料無料（保険付き）。無地・ノーブランドの外箱で、ドイツから発送いたします。$399以上で送料無料（保険付き）。 注文手続きを開始すると、レートは30分間ロックされます。レートは30分間ロック。 すべての商品は未開封で、シリアル番号を確認した上で、24か月保証が付いています。未開封、24か月保証。

ウォッチリスト ログイン
Green circuit board with black memory chips and gold edge connector

OWC

OWC 8GB DDR3 1600 CL11 2Rx8 1.5V Non-ECC DIMM for OptiPlex 9020

SKU CH-BV2V-SGZP4

An 8 GB DDR3-1600 CL11 DIMM validated for Dell OptiPlex 9020 Micro, SFF, Tower and USFF systems

  • Capacity8GB
  • Type240-Pin DDR3 Non-ECC UDIMM
  • SpeedDDR3 1600 (PC3 12800)
  • CAS LatencyCL11
  • Voltage1.5V
  • ECCNo
  • 8GB single module expands OptiPlex 9020 capacity
  • DDR3 1600 CL11 matches factory speed and timing
  • 5V unbuffered design drops in without BIOS changes
  • JEDEC and RoHS compliant for warranty-safe upgrade
  • Fits Micro SFF Tower and USFF chassis variants

OWC 8GB DDR3 1600 DIMM for OptiPlex 9020

This 8GB DDR3 1600 CL11 module is built for Dell OptiPlex 9020 Micro, SFF, Tower and USFF desktops. It uses a 240-pin unbuffered non-ECC design at 1.5V. The single DIMM adds memory capacity to supported systems without requiring configuration changes. Buyers who need ECC protection or registered modules cannot use this product.

JEDEC-standard DDR3 1600 sustained operation

The module meets JEDEC PC3-12800 specifications and runs at the rated 1600 speed with CL11 latency under continuous load. 2Rx8 organisation allows the memory controller to interleave accesses across ranks, helping maintain throughput during extended multitasking sessions. No heat spreader is fitted, so airflow in the chassis determines thermal headroom. Builders who want overclocking headroom or lower latency timings cannot achieve them with this specification.

Tool-free DIMM installation in OptiPlex chassis

Installation follows the standard 240-pin DIMM procedure: align the notch, press until the retention clips engage, then verify detection in BIOS. The OptiPlex 9020 Micro and USFF layouts place slots in tight spaces, so fingers may need to reach past drive cages or power cables. Systems that already populate every slot with mismatched ranks or speeds may fail to post until the configuration is uniform. Buyers who lack physical access to the motherboard or cannot open the chassis cannot complete the upgrade.

特長

  • 8GB single module expands OptiPlex 9020 capacity
  • DDR3 1600 CL11 matches factory speed and timing
  • 5V unbuffered design drops in without BIOS changes
  • JEDEC and RoHS compliant for warranty-safe upgrade
  • Fits Micro SFF Tower and USFF chassis variants

仕様

BrandOWC
Part Number1U6D32R808GB
Capacity8GB
Type240-Pin DDR3 Non-ECC UDIMM
SpeedDDR3 1600 (PC3 12800)
CAS LatencyCL11
Voltage1.5V
ECCNo
Buffered/RegisteredUnbuffered
Rank2Rx8
Heat SpreaderNo
Compatible SystemDell OptiPlex 9020 Micro
Dell OptiPlex 9020 SFF
Dell OptiPlex 9020 Tower
Dell OptiPlex 9020 USFF

このモデルの他のバージョン

同シリーズにさらに 5点

同じファミリーで、メモリ・クーラー・クロックが異なります — 購入前に比較してください。

この商品に関する質問

Does the 1.5 V DDR3 module run hot or draw extra power when the OptiPlex 9020 is under load all day?

The JEDEC-standard 1.5 V DDR3 DIMM operates at its rated voltage without overclocking, so heat and power stay within normal desktop limits during continuous use.

What must the OptiPlex 9020 already have — free 240-pin slots and a matching DDR3 controller — for this 8 GB stick to work?

The system needs an available 240-pin DDR3 UDIMM slot and a memory controller that supports PC3-12800 CL11 timing; all four 9020 form factors meet that requirement.

Will this 2Rx8 CL11 module slow down if I keep the original 1Rx8 sticks in the other channels?

The memory controller will run all populated channels at the lowest common speed and latency, so the original modules set the pace for the new 8 GB DIMM.

同じ売り場の商品

よく比較されている商品

同じ売り場、同じレジ — 8種類のコインと30分間のレートロック。