我們接受加密貨幣付款 — 讓您持有的幣種也能買到真正的硬體設備。以加密貨幣付款，直接購入真正的硬體設備。 全球訂單滿 US$399，即享免費保險運送。簡約外箱，不印任何品牌標誌，從德國出貨。訂單滿 US$399，即享免費保險運送。 結帳一開始，您的匯率即鎖定 30 分鐘。匯率鎖定 30 分鐘。 每件商品皆原廠密封、序號經過核對，並享有 24 個月保固。原廠密封，保固 24 個月。

追蹤清單 登入
Green circuit board with black memory chips and gold edge connector

OWC

OWC 8GB DDR3 1600 CL11 2Rx8 1.5V Non-ECC DIMM for OptiPlex 9020

SKU CH-BV2V-SGZP4

An 8 GB DDR3-1600 CL11 DIMM validated for Dell OptiPlex 9020 Micro, SFF, Tower and USFF systems

  • Capacity8GB
  • Type240-Pin DDR3 Non-ECC UDIMM
  • SpeedDDR3 1600 (PC3 12800)
  • CAS LatencyCL11
  • Voltage1.5V
  • ECCNo
  • 8GB single module expands OptiPlex 9020 capacity
  • DDR3 1600 CL11 matches factory speed and timing
  • 5V unbuffered design drops in without BIOS changes
  • JEDEC and RoHS compliant for warranty-safe upgrade
  • Fits Micro SFF Tower and USFF chassis variants

OWC 8GB DDR3 1600 DIMM for OptiPlex 9020

This 8GB DDR3 1600 CL11 module is built for Dell OptiPlex 9020 Micro, SFF, Tower and USFF desktops. It uses a 240-pin unbuffered non-ECC design at 1.5V. The single DIMM adds memory capacity to supported systems without requiring configuration changes. Buyers who need ECC protection or registered modules cannot use this product.

JEDEC-standard DDR3 1600 sustained operation

The module meets JEDEC PC3-12800 specifications and runs at the rated 1600 speed with CL11 latency under continuous load. 2Rx8 organisation allows the memory controller to interleave accesses across ranks, helping maintain throughput during extended multitasking sessions. No heat spreader is fitted, so airflow in the chassis determines thermal headroom. Builders who want overclocking headroom or lower latency timings cannot achieve them with this specification.

Tool-free DIMM installation in OptiPlex chassis

Installation follows the standard 240-pin DIMM procedure: align the notch, press until the retention clips engage, then verify detection in BIOS. The OptiPlex 9020 Micro and USFF layouts place slots in tight spaces, so fingers may need to reach past drive cages or power cables. Systems that already populate every slot with mismatched ranks or speeds may fail to post until the configuration is uniform. Buyers who lack physical access to the motherboard or cannot open the chassis cannot complete the upgrade.

商品特色

  • 8GB single module expands OptiPlex 9020 capacity
  • DDR3 1600 CL11 matches factory speed and timing
  • 5V unbuffered design drops in without BIOS changes
  • JEDEC and RoHS compliant for warranty-safe upgrade
  • Fits Micro SFF Tower and USFF chassis variants

商品規格

BrandOWC
Part Number1U6D32R808GB
Capacity8GB
Type240-Pin DDR3 Non-ECC UDIMM
SpeedDDR3 1600 (PC3 12800)
CAS LatencyCL11
Voltage1.5V
ECCNo
Buffered/RegisteredUnbuffered
Rank2Rx8
Heat SpreaderNo
Compatible SystemDell OptiPlex 9020 Micro
Dell OptiPlex 9020 SFF
Dell OptiPlex 9020 Tower
Dell OptiPlex 9020 USFF

其他版本

同系列還有 5 款

同系列產品，記憶體、散熱器或時脈不同 — 下單前請先比較。

商品問答

Does the 1.5 V DDR3 module run hot or draw extra power when the OptiPlex 9020 is under load all day?

The JEDEC-standard 1.5 V DDR3 DIMM operates at its rated voltage without overclocking, so heat and power stay within normal desktop limits during continuous use.

What must the OptiPlex 9020 already have — free 240-pin slots and a matching DDR3 controller — for this 8 GB stick to work?

The system needs an available 240-pin DDR3 UDIMM slot and a memory controller that supports PC3-12800 CL11 timing; all four 9020 form factors meet that requirement.

Will this 2Rx8 CL11 module slow down if I keep the original 1Rx8 sticks in the other channels?

The memory controller will run all populated channels at the lowest common speed and latency, so the original modules set the pace for the new 8 GB DIMM.

同類商品

顧客也比較過

同一分類，同一套結帳流程 — 支援八種加密貨幣，匯率鎖定 30 分鐘。