暗号資産でのお支払いに対応—お手持ちのコインで、本物のハードウェアをご購入いただけます。暗号資産で支払い、本物のハードウェアに使う。 $399以上のご注文で、世界中どこでも送料無料（保険付き）。無地・ノーブランドの外箱で、ドイツから発送いたします。$399以上で送料無料（保険付き）。 注文手続きを開始すると、レートは30分間ロックされます。レートは30分間ロック。 すべての商品は未開封で、シリアル番号を確認した上で、24か月保証が付いています。未開封、24か月保証。

ウォッチリスト ログイン
Green circuit board with gold edge connectors and black memory chips

OWC

OWC 8GB DDR4 2400 CL17 1Rx8 UDIMM QNAP TS-677/832 series

SKU CH-Y32C-BWHR5

Adds 8GB of DDR4 2400 CL17 memory to compatible QNAP TS-677 and TS-832 series NAS units

  • Capacity8GB
  • Type288-Pin DDR4 Non-ECC UDIMM
  • SpeedDDR4 2400 (PC4 19200)
  • CAS LatencyCL17
  • Voltage1.2V
  • ECCNo
  • Boosts NAS responsiveness with 8 GB DDR4 2400 CL17 module
  • JEDEC-standard 1.2 V unbuffered DIMM ensures warranty-safe upgrade
  • Single 1Rx8 288-pin stick installs in minutes without tools
  • Backward compatible with 2133 MHz systems for flexible deployment
  • Replaces QNAP part numbers RAM-8GDR4A0-UD-2400 and RAM-8GDR4A1-UD-2400

OWC 8GB DDR4 2400 UDIMM for QNAP NAS

This 8GB DDR4 2400 CL17 UDIMM module is built for QNAP TS-677, TS-832PXU, TS-832PXU-RP, TS-832XU and TS-832XU-RP systems. It replaces QNAP part numbers RAM-8GDR4A0-UD-2400 and RAM-8GDR4A1-UD-2400. The module suits administrators expanding memory in these specific NAS units. Buyers needing ECC registered memory or capacities beyond 8GB per slot cannot use this part.

Installation is a standard UDIMM insertion

The 288-pin unbuffered DIMM fits the memory slots on the listed QNAP models without tools. Align the notch, press firmly until the retention clips click, then power on to verify the new capacity. The most common issue is seating the module incompletely, which leaves the system showing the original memory total. Reseating usually resolves this. No BIOS configuration is required on these appliances.

The decisive specification is 1Rx8 CL17 at 1.2V

This single-rank by eight organisation with CL17 latency matches the OEM timing the QNAP firmware expects. The JEDEC-standard 1.2V operation ensures compatibility with the platform's memory controller. Systems requiring dual-rank modules, lower latency bins or 1.35V operation will not work correctly with this module. Backward compatibility with 2133MHz buses is supported.

特長

  • Boosts NAS responsiveness with 8 GB DDR4 2400 CL17 module
  • JEDEC-standard 1.2 V unbuffered DIMM ensures warranty-safe upgrade
  • Single 1Rx8 288-pin stick installs in minutes without tools
  • Backward compatible with 2133 MHz systems for flexible deployment
  • Replaces QNAP part numbers RAM-8GDR4A0-UD-2400 and RAM-8GDR4A1-UD-2400

仕様

BrandOWC
Part Number2U4D41R808GB
Capacity8GB
Type288-Pin DDR4 Non-ECC UDIMM
SpeedDDR4 2400 (PC4 19200)
CAS LatencyCL17
Voltage1.2V
ECCNo
Buffered/RegisteredUnbuffered
Rank1Rx8
Heat SpreaderNo
Compatible SystemQNAP TS-677
QNAP TS-832PXU
QNAP TS-832PXU-RP
QNAP TS-832XU
QNAP TS-832XU-RP

このモデルの他のバージョン

同シリーズにさらに 5点

同じファミリーで、メモリ・クーラー・クロックが異なります — 購入前に比較してください。

この商品に関する質問

How can I confirm the module is running at 2400MHz CL17 after installing it in my TS-832XU?

Open the QNAP system information page or BIOS; the memory section should report DDR4 2400 (PC4-19200) with a CAS latency of 17 for the new module.

What comes in the package and do I need any extra parts to fit it into a TS-677?

The box contains one 8GB 288-pin DDR4 UDIMM; no additional brackets, cables or tools are required for installation.

Should I pick the 8GB 1Rx8 CL17 stick or look for a different rank or latency for my TS-832PXU?

This 8GB 1Rx8 CL17 module matches the QNAP part numbers RAM-8GDR4A0-UD-2400 and RAM-8GDR4A1-UD-2400, so it is the correct specification for those models.

同じ売り場の商品

よく比較されている商品

同じ売り場、同じレジ — 8種類のコインと30分間のレートロック。