暗号資産でのお支払いに対応—お手持ちのコインで、本物のハードウェアをご購入いただけます。暗号資産で支払い、本物のハードウェアに使う。 $399以上のご注文で、世界中どこでも送料無料（保険付き）。無地・ノーブランドの外箱で、ドイツから発送いたします。$399以上で送料無料（保険付き）。 注文手続きを開始すると、レートは30分間ロックされます。レートは30分間ロック。 すべての商品は未開封で、シリアル番号を確認した上で、24か月保証が付いています。未開封、24か月保証。

ウォッチリスト ログイン
Small black 40 by 20 millimetre axial case fan with two wires

Zyvpee

Zyvpee KDE1204PKV1 40x20mm 12V .8W 2-wire case fan

SKU CH-BZ7F-1283C

A 40 mm square by 20 mm thick axial fan runs on 12 V DC at .8 W with Maglev bearings and a 2-wire power connector

  • TypeCase Fan
  • CompatibilityCase
  • Bearing TypeMaglev
  • Power Connector2 wires
  • ColorBlack
  • LEDNon-LED
  • Maglev bearing reduces friction for quiet operation
  • 12 V, .8 W draw keeps power use low
  • 40 mm by 20 mm frame fits tight 4 cm spaces
  • Two-wire DC connection simplifies installation
  • Non-LED black design suits stealth builds

Zyvpee KDE1204PKV1 40x20mm case fan

This 40mm square axial fan fits standard case mounting points. It runs on 12V DC power and draws .8W. The Maglev bearing reduces friction and noise. Two wires supply power without speed reporting.

Suits tight 40mm mounts needing low power draw

Builders who need PWM speed control or a three or four wire header should look elsewhere. The two wire design only supports voltage regulation. Buyers wanting RGB lighting or higher airflow will need a different model.

Two wire 12V .8W power connector

The 2 wire connector delivers fixed 12V power at .8W. No tachometer or PWM signal is present. Speed varies only with voltage changes. Check that your board or controller provides a compatible two pin header.

特長

  • Maglev bearing reduces friction for quiet operation
  • 12 V, .8 W draw keeps power use low
  • 40 mm by 20 mm frame fits tight 4 cm spaces
  • Two-wire DC connection simplifies installation
  • Non-LED black design suits stealth builds

仕様

SeriesKDE1204PKV1
ModelKDE1204PKV1
TypeCase Fan
CompatibilityCase
Bearing TypeMaglev
Power Connector2 wires
ColorBlack
LEDNon-LED
FeaturesDC axial fan
Dimensions40*40*20mm

この商品に関する質問

Will the 40×20 mm frame with 2-wire lead fit my case fan mount?

The fan measures 40 mm square by 20 mm thick and uses a two-wire DC connection, so it fits any 40 mm mounting holes that accept a 20 mm deep frame.

How do I connect the two wires to a 12 V header without reversing polarity?

Match the red wire to the 12 V pin and the black wire to ground on the motherboard or controller header; reversing them will prevent the maglev motor from starting.

Does the maglev bearing need lubrication or replacement over time?

The magnetic-levitation bearing runs without contact, so no lubrication is required and there is no wearable sleeve or ball to replace.

同じ売り場の商品

よく比較されている商品

同じ売り場、同じレジ — 8種類のコインと30分間のレートロック。