SanDisk
SanDisk Cruzer Blade 8 GB USB 2.0 USB flash drive Black SDCZ50-008G-B35
US$391.99
0.00501927BTC
재고 있음
A-Tech
A-Tech 4GB DDR3 1333 ECC UDIMM 2Rx8 HP 500210-071 500210-571 server RAM
4GB DDR3 1333 ECC unbuffered DIMM for HP 500210-071 and 500210-571 servers
- Capacity4GB
- SpeedDDR3 1333 (PC3 10600)
- CAS LatencyCL9
- Voltage1.50V
- ECCYes
- Buffered/RegisteredUnbuffered
- 4GB capacity expands server memory headroom for heavier workloads
- DDR3 1333 MHz speed matches PC3-10600 system bus timing
- ECC UDIMM design detects and corrects single-bit data errors
- 240-pin unbuffered form factor fits standard DDR3 DIMM slots
- Replaces HP part numbers 500210-071 and 500210-571
4GB DDR3 1333 ECC UDIMM for HP Servers
This 4GB DDR3 1333 (PC3-10600) module is an unbuffered ECC UDIMM built with a 2Rx8 organisation. It runs at the standard 1.5V and carries a CL9 latency rating. The 240-pin DIMM is designed as a direct replacement for HP part numbers 500210-071 and 500210-571 in compatible server and workstation platforms.
Sustained load behaviour with ECC protection
Error-correcting code detects and corrects single-bit errors during continuous operation, helping to prevent data corruption under heavy, long-running workloads. Unbuffered architecture keeps latency low for each access while the 2Rx8 rank layout allows the memory controller to interleave across ranks. The 1.5V supply remains within standard DDR3 limits, so thermal output stays consistent during extended use.
Verify platform support before ordering
Confirm that your system accepts DDR3 1333 ECC UDIMM modules in a 240-pin slot and that the firmware enables ECC on unbuffered DIMMs. Check the maximum supported capacity per slot and the total number of populated channels allowed by the memory controller. Ensure the motherboard or server board is qualified for 2Rx8 rank configurations at this speed and voltage.
주요 특징
- 4GB capacity expands server memory headroom for heavier workloads
- DDR3 1333 MHz speed matches PC3-10600 system bus timing
- ECC UDIMM design detects and corrects single-bit data errors
- 240-pin unbuffered form factor fits standard DDR3 DIMM slots
- Replaces HP part numbers 500210-071 and 500210-571
사양
| Brand | A-Tech |
|---|---|
| Capacity | 4GB |
| Speed | DDR3 1333 (PC3 10600) |
| CAS Latency | CL9 |
| Voltage | 1.50V |
| ECC | Yes |
| Buffered/Registered | Unbuffered |
| Rank | 2Rx8 |
| Chipset | Major Brand Chipset |
| Features | Major Brand Chips |
이 상품에 대한 질문
Does this 1.50 V DDR3 1333 module draw much power or generate extra heat when the server runs all day?
It operates at standard 1.50 V DDR3 voltage, so power draw and heat output are typical for a 4 GB DDR3 1333 ECC UDIMM under continuous load.
What must the motherboard provide for this 240-pin DDR3 ECC UDIMM to work?
A DDR3 DIMM slot that accepts unbuffered ECC modules at 1.5 V and supports 2Rx8 organisation.
Will this DDR3 1333 CL9 stick work in a system that currently runs slower DDR3 modules?
The module runs at DDR3 1333 (PC3-10600) CL9; the motherboard will set the common speed for all installed DIMMs.
이 진열대의 다른 상품
고객들이 함께 비교한 상품
같은 진열대, 같은 체크아웃 — 코인 8종, 환율 잠금 30분.
