저희는 암호화폐로 결제를 받습니다 — 보유하신 코인으로 실제 하드웨어를 구매하실 수 있습니다.암호화폐로 결제하고, 실제 하드웨어 구매에 사용하십시오. 전 세계 어디서나 US$399 이상 구매 시 무료 보험 배송. 무지 상자에 담아 독일에서 발송합니다.US$399 이상 구매 시 무료 보험 배송. 체크아웃을 시작하면 30분 동안 환율이 잠깁니다.30분간 환율 잠금. 모든 제품은 밀봉된 상태로 일련번호를 확인한 후 24개월 보증을 제공합니다.밀봉 포장, 24개월 보증.

가격 추적 로그인
Green Arduino shield board with motor driver chips and screw terminals

Arduino

Arduino Motor Shield R3 development board

SKU CH-BP0N-11ZH9

A dual full-bridge driver shield based on the L298 that independently controls speed and direction for two DC motors and measures current absorption

  • Drives two DC motors independently with L298 dual full-bridge driver
  • Measures current absorption per motor for load monitoring
  • TinkerKit compatible for rapid plug-and-play prototyping
  • Requires external power via 2.1 mm jack or Vin/GND screw terminals
  • Separate logic and motor supply rails protect the host board

Arduino Motor Shield R3

The Arduino Motor Shield R3 is a development board built around the L298 dual full-bridge driver. It enables an Arduino board to drive inductive loads such as DC motors, stepping motors, relays and solenoids. The shield is TinkerKit compatible for rapid project creation using plug-in modules. It suits makers and students building motorised prototypes.

Dual DC motor control with current sensing

The shield drives two DC motors independently, managing speed and direction for each channel. It also provides motor current absorption measurement for monitoring load conditions. The L298 driver requires an external power supply because motor current often exceeds the USB current rating. It cannot be powered from the USB connection alone.

External power via adapter or battery

Power is supplied through a 2.1 mm centre-positive plug into the host Arduino board or via Vin and GND screw terminals on the shield. Separate logic and motor supply connections on the L298 protect the Arduino board from damage. Correct polarity must be observed when wiring the screw terminals. The shield mounts directly onto an Arduino board.

주요 특징

  • Drives two DC motors independently with L298 dual full-bridge driver
  • Measures current absorption per motor for load monitoring
  • TinkerKit compatible for rapid plug-and-play prototyping
  • Requires external power via 2.1 mm jack or Vin/GND screw terminals
  • Separate logic and motor supply rails protect the host board

사양

이 상품에 대해 아직 공개된 사양이 없습니다.

이 상품에 대한 질문

Will the L298 driver on this shield control two DC motors from my existing Arduino Uno without extra wiring?

The shield plugs directly onto an Arduino board and drives two DC motors independently using the L298 dual full-bridge driver, controlling speed and direction for each channel.

How can I confirm the motor current sensing is working after I mount the shield?

You can read the analog current-sense pins for each channel in your sketch to monitor real-time motor current absorption while the motors run.

Does the box include the 2.1 mm center-positive power adapter or must I source it separately?

The shield requires an external power supply; the adapter or battery is not included and must be provided separately, connected via the 2.1 mm jack or Vin and GND screw terminals.

이 진열대의 다른 상품

고객들이 함께 비교한 상품

같은 진열대, 같은 체크아웃 — 코인 8종, 환율 잠금 30분.