Akceptujemy kryptowaluty — posiadane środki można więc wykorzystać na zakup prawdziwego sprzętu.Płatność kryptowalutą — realny sprzęt w zamian. Bezpłatna, ubezpieczona dostawa na całym świecie powyżej 399 $. Neutralne kartony, bez oznaczeń, wysyłane z Niemiec.Bezpłatna, ubezpieczona dostawa powyżej 399 $. Kurs zostaje zablokowany na 30 minut od otwarcia kasy.Kurs zablokowany na 30 minut. Każdy produkt jest fabrycznie zapieczętowany, jego numer seryjny jest sprawdzany, a całość objęta jest 24-miesięczną gwarancją.Zapieczętowane fabrycznie, 24 miesiące gwarancji.

Obserwowane produkty Zaloguj się
Two 70 mm two-tone fans with 4-pin connectors

OEM Industries

OEM Industries FD7010H12S 12V .35A 4-pin fan pair for XFX 8010

SKU CH-0E10-D007H

A pair of 12 V sleeve-bearing fans with four-pin connectors for the XFX 8010 cooler

  • Color2-Tone
  • TypeFan only
  • Bearing TypeSleeve Bearing
  • Power Connector4 Pin
  • LEDNo
  • Supplied as a matched pair for balanced airflow
  • 12 V .35 A rating keeps power draw low
  • Four-wire four-pin connector enables PWM speed control
  • Sleeve bearing runs quietly at typical desktop loads
  • Designed as a direct fit for the XFX 8010 heatsink

Replacement Fan Pair for XFX 8010

This two-piece set supplies matching FD7010H12S fans built for the XFX 8010 cooler. Each unit draws 12 V at .35 A through a standard 4-pin connector. The sleeve bearing keeps the assembly simple and cost-effective. Buyers needing PWM control for a different cooler should look elsewhere.

Four-Pin Power and Speed Limits

The 4-pin header allows the motherboard to regulate speed, but the sleeve bearing caps long-term high-RPM reliability. Continuous operation at maximum voltage may shorten lifespan compared with ball-bearing alternatives. No LED lighting or specialised control firmware is present. Systems requiring rated MTBF data for server duty will not find it here.

Straightforward Drop-In Installation

Alignment pins on the XFX 8010 shroud guide the frames into place, so no adapters or soldering are needed. The only common snag is routing the paired cables past tight VRM heatsinks without straining the connectors. Builders working in cramped ITX chassis should verify clearance before ordering.

Najważniejsze cechy

  • Supplied as a matched pair for balanced airflow
  • 12 V .35 A rating keeps power draw low
  • Four-wire four-pin connector enables PWM speed control
  • Sleeve bearing runs quietly at typical desktop loads
  • Designed as a direct fit for the XFX 8010 heatsink

Specyfikacja

ModelFD7010H12S
Color2-Tone
TypeFan only
Bearing TypeSleeve Bearing
Power Connector4 Pin
LEDNo

Pytania dotyczące tego produktu

Are these the FD7010H12S 4-pin fans intended for the XFX 8010 cooler?

Yes, the pair is sold specifically as FD7010H12S units with a 4-pin connector for the XFX 8010 heatsink.

What does the 12 V .35 A rating mean once the fans are installed?

Each fan draws 0.35 A at 12 V, so the motherboard header must supply at least that current per fan for full speed operation.

How does the 4-pin connector affect speed control on the XFX 8010?

The 4-pin PWM connection lets the motherboard vary fan speed precisely, rather than relying on voltage-only regulation.

Także w tym dziale

Klienci porównywali też te produkty

Ten sam dział, ta sama kasa — osiem kryptowalut i 30-minutowa blokada kursu.