Akceptujemy kryptowaluty — posiadane środki można więc wykorzystać na zakup prawdziwego sprzętu.Płatność kryptowalutą — realny sprzęt w zamian. Bezpłatna, ubezpieczona dostawa na całym świecie powyżej 399 $. Neutralne kartony, bez oznaczeń, wysyłane z Niemiec.Bezpłatna, ubezpieczona dostawa powyżej 399 $. Kurs zostaje zablokowany na 30 minut od otwarcia kasy.Kurs zablokowany na 30 minut. Każdy produkt jest fabrycznie zapieczętowany, jego numer seryjny jest sprawdzany, a całość objęta jest 24-miesięczną gwarancją.Zapieczętowane fabrycznie, 24 miesiące gwarancji.

Obserwowane produkty Zaloguj się
Black 70mm square case fan 25mm thick with three-pin connector

Zyvpee

Zyvpee 2810KL-S4W-B39 70mm 25mm 3-pin ball-bearing case fan

SKU CH-MGWA-18GBW

70 mm ball-bearing case fan runs at 12 V and 0.19 A with a three-pin connector

  • TypeCase Fan
  • Bearing TypeBall
  • Power Connector3 Pin
  • ColorBlack
  • LEDNon-LED
  • FeaturesCasse Fan
  • Ball-bearing design reduces friction for longer life
  • 12 V 0.19 A power draw keeps energy use low
  • 70 mm by 25 mm frame fits tight chassis spaces
  • Three-pin connector enables speed monitoring
  • Non-LED black finish suits stealth builds

Compact 70 mm Case Fan

The Zyvpee 2810KL-S4W-B39 is a 70 mm square case fan designed for tight chassis spaces or targeted component cooling. Its ball-bearing motor and 3-pin power connector suit system builders who need a straightforward replacement or supplementary airflow device. The non-LED black frame keeps the appearance neutral in any build.

Check Connector And Clearance

Verify that your motherboard or fan controller provides a standard 3-pin header before ordering. Confirm the mounting holes match a 70 mm square pattern and that 25 mm thickness fits the intended location, whether on a case panel, heatsink or radiator. The fan draws 0.19 A at 12 V, so ensure the header can supply that current.

Ball Bearing Thermals And Acoustics

The ball-bearing design delivers consistent rotation with reduced friction compared to sleeve alternatives, supporting steady airflow in daily operation. Power draw is 0.19 A at 12 V, resulting in modest heat contribution to the loop. Expect typical mechanical noise from a 70 mm frame at operating speed without LED illumination adding electrical load.

Najważniejsze cechy

  • Ball-bearing design reduces friction for longer life
  • 12 V 0.19 A power draw keeps energy use low
  • 70 mm by 25 mm frame fits tight chassis spaces
  • Three-pin connector enables speed monitoring
  • Non-LED black finish suits stealth builds

Specyfikacja

BrandZyvpee
Series2810KL-S4W-B39 XA1
Model2810KL-S4W-B39
TypeCase Fan
Bearing TypeBall
Power Connector3 Pin
ColorBlack
LEDNon-LED
FeaturesCasse Fan
Dimensions70*25MM

Pytania dotyczące tego produktu

Does the 70 mm fan ship with mounting screws or do I need to buy them separately?

The fan is supplied as a standalone unit; mounting hardware is not included and must be sourced separately.

The model 2810KL-S4W-B39 lists 12 V 0.19 A — is there an alternative voltage or current version to choose from?

Only the 12 V 0.19 A variant is offered; no other voltage or current options are available for this model.

What does the 3-pin connector mean for speed control once the fan is installed in a case?

The three-pin interface provides power, ground and a tachometer signal, allowing the motherboard to monitor RPM but not to vary voltage for PWM speed regulation.

Także w tym dziale

Klienci porównywali też te produkty

Ten sam dział, ta sama kasa — osiem kryptowalut i 30-minutowa blokada kursu.