BFKK 3U Rackmount Server Chassis EATX/ATX/MATX 4x5.25 6x3.5 Top/Side Cooling
- Rackmount
Prijímame kryptomeny — takže mince, ktoré držíte, môžete zameniť za skutočný hardvér.Plaťte v krypte, miňte ho na skutočný hardvér. Poistená doprava zadarmo po celom svete nad 399 $. Neutrálne kartóny bez potlače, odosielané z Nemecka.Poistená doprava zadarmo nad 399 $. Váš kurz je zablokovaný na 30 minút hneď po otvorení pokladne.Kurz zablokovaný na 30 minút. Každý produkt je zapečatený, jeho sériové číslo je overené a vzťahuje sa naň 24-mesačná záruka.Zapečatené, 24-mesačná záruka.
Mean Well
240 W LED driver delivers 24 V at 10 A with up to 94 % efficiency, active PFC and IP67/IP65 protection for indoor or outdoor lighting
The Mean Well HLG-240H-24 is a 24 V, 10 A switching power supply designed for LED lighting and street lighting applications. It accepts a universal AC input up to 305 VAC and delivers 240 W through a single output. The IP67 and IP65 rated enclosure suits both indoor and outdoor installations. It meets Type HL requirements for Class I, Division 2 hazardous locations.
Replacing an unsealed or lower-efficiency driver with this unit adds active PFC and up to 94% efficiency, reducing waste heat and improving power factor. The jump is worth it when installations demand IP67 or IP65 ingress protection, 4 kV surge immunity per IEC 61000-4-5, or adjustable output current for precise LED drive. Builders needing only basic indoor coverage without dimming or surge rating may not require this specification.
Cooling relies on free air convection, so sustained output depends on ambient airflow rather than forced fans. The built-in protections — short circuit, over current, over voltage and over temperature — maintain safe operation during prolonged use. High efficiency up to 94% minimises internal heat rise, supporting reliable performance in sealed outdoor enclosures where active cooling is impractical.
| Type | AT |
|---|
The unit cools by free air convection, so leave open space around the housing; do not seal it inside an insulated cavity or stack items against the fins.
Connect the dimming leads (1-10 VDC, PWM, or resistance) to the correct terminals and verify polarity before applying mains power.
Verify the output current setting after the first 24 hours of operation and again if the load changes or ambient temperature shifts significantly.
Aj v tomto oddelení
Rovnaké oddelenie, rovnaká pokladňa — osem mien a kurz zablokovaný na 30 minút.
Mena, v ktorej platíte, a mena, v ktorej sa zobrazujú ceny.
Odoslané z vašej peňaženky na pokladni
Len na zobrazenie — katalóg je uvedený v dolároch
Žiadna mena nezodpovedá.
Vyberte jazyk, v ktorom s vami bude web komunikovať.
Žiadny jazyk nezodpovedá.
Ste tu prvýkrát?
Účet už máte?
Automatický reset hesla neexistuje: tento obchod neposiela žiadne e-maily, takže neexistuje jednorazový odkaz, o ktorý by ste mohli požiadať. Nechajte adresu na účte — niekto sa jej ujme ručne.
Žiadosť zaznamenaná
Do vašej schránky nič nepríde — tento obchod neposiela vôbec žiadne e-maily. Niekto sa o to postará ručne.
Spomenuli ste si?