EN-Labs 11-001-366 PCIe x4 USB 3.2 10Gbps 5-port card
- no
- 12CM Case fan,screw…
نقبل الدفع بالعملة المشفرة — لذلك يمكن للعملات الرقمية التي تملكها أن تشتري أجهزة حقيقية.ادفع بالعملة المشفرة، وأنفقها على أجهزة حقيقية. شحن مؤمن مجانا إلى كل أنحاء العالم لما يتجاوز 399 US$. صناديق شحن بسيطة بلا علامة تجارية، ترسل من ألمانيا.شحن مؤمن مجانا لما يتجاوز 399 US$. يُقفل سعرك لمدة 30 دقيقة بمجرد فتح صفحة الدفع.السعر مقفل لمدة 30 دقيقة. كل قطعة مختومة، ورقمها التسلسلي متحقق منه، ومشمولة بضمان 24 شهرا.مختوم، وبضمان 24 شهرا.
A-Tech
A 16 GB DDR4 2133 MHz ECC registered DIMM with dual-rank chips, Supermicro certified for server reliability
This 16GB DDR4 2133MHz module is built for servers and workstations that require error-correcting registered memory. It uses a 2Rx4 dual-rank layout and runs at the standard 1.20V voltage. The stick carries Supermicro certification for the MEM-DR416L-HL01-ER21 part number.
At CL15 latency the module delivers consistent throughput during extended workloads rather than only in short bursts. Registered buffering reduces electrical load on the memory controller, helping stability when all slots are populated. ECC circuitry corrects single-bit errors on the fly to prevent data corruption over long runs.
Verify that your motherboard supports DDR4 RDIMM modules at 2133MHz with ECC registered operation. The 288-pin form factor fits standard DDR4 server slots, but some consumer boards cannot use registered memory. Confirm the maximum supported capacity per slot and total population rules in your system documentation.
| Brand | SuperMicro |
|---|---|
| Series | Supermicro Certified |
| Model | MEM-DR416L-HL01-ER21 |
| Capacity | 16GB |
| Speed | DDR4 2133 (PC4 17000) |
| CAS Latency | CL15 |
| Voltage | 1.20V |
| ECC | Yes |
| Buffered/Registered | Registered |
| Rank | 2Rx4 |
| Chipset | Major Brand Chipset |
| Features | Supermicro Certified MEM-DR416L-HL01-ER21 (HMA42GR7MFR4N-TF) |
At the standard 1.20V DDR4 voltage the 16GB RDIMM operates within normal server memory power envelopes; exact sustained draw depends on workload and platform but no elevated voltage is required.
The board must provide DDR4 RDIMM slots that support ECC Registered memory and accept 2Rx4 modules at 2133MHz.
It can run with other DDR4 2133MHz ECC Registered DIMMs, though mixing ranks or CAS latencies may force the system to the slowest common timing.
أيضًا في هذا القسم
نفس القسم، ونفس صفحة الدفع — ثماني عملات رقمية وقفل سعر لمدة 30 دقيقة.
ما تدفعه، وما تُعرض به الأسعار.
يُرسَل من محفظتك عند إتمام الطلب
للعرض فقط — أسعار الكتالوج بالدولار الأمريكي
لا توجد عملة مطابقة.
اختر اللغة التي يخاطبك بها الموقع.
هل أنت جديد هنا؟
لديك حساب بالفعل؟
لا توجد إعادة تعيين تلقائية: هذا المتجر لا يُرسل أي بريد، فلا يوجد رابط لمرة واحدة يمكن طلبه. اترك العنوان في الحساب، وسيُعالَج الأمر يدويًا.
تم تسجيل الطلب
لا شيء في طريقه إلى بريدك الوارد — هذا المتجر لا يُرسل أي بريد إطلاقًا. يتولّى أحدهم معالجة هذه الطلبات يدويًا.
تذكّرتها؟