A-Tech 2GB DDR2 667MHz PC2-5300 UDIMM CL5 1.8V 240-Pin Desktop RAM
- 2GB
- DDR2 667 (PC2 5300)
نقبل الدفع بالعملة المشفرة — لذلك يمكن للعملات الرقمية التي تملكها أن تشتري أجهزة حقيقية.ادفع بالعملة المشفرة، وأنفقها على أجهزة حقيقية. شحن مؤمن مجانا إلى كل أنحاء العالم لما يتجاوز 399 US$. صناديق شحن بسيطة بلا علامة تجارية، ترسل من ألمانيا.شحن مؤمن مجانا لما يتجاوز 399 US$. يُقفل سعرك لمدة 30 دقيقة بمجرد فتح صفحة الدفع.السعر مقفل لمدة 30 دقيقة. كل قطعة مختومة، ورقمها التسلسلي متحقق منه، ومشمولة بضمان 24 شهرا.مختوم، وبضمان 24 شهرا.
A-Tech
A 2 GB dual-channel kit of DDR2 800 MHz desktop memory running at 1.8 V with CL6 timing on 240-pin DIMMs
Capacity 2GB (2 x 1GB)
Speed DDR2 800 (PC2 6400)
This A-Tech kit delivers 2GB of DDR2 memory as two matched 1GB modules running at 800MHz with PC2-6400 bandwidth. The unbuffered, non-ECC DIMMs operate at the standard 1.8V DDR2 voltage and use the 240-pin desktop form factor. It is designed as a straightforward capacity upgrade for compatible desktop systems.
The dual-channel configuration benefits owners of older AMD and Intel desktop platforms that support DDR2 800MHz memory and have two available DIMM slots. Systems requiring ECC, registered modules, or a different DDR generation will not accept this kit, so verifying the motherboard specification is essential before purchase.
The modules use the 240-pin DDR2 DIMM interface, which is the single physical and electrical specification that determines whether they fit and function in a given motherboard. Only boards designed for DDR2 memory with this pin layout can use the kit.
| Brand | A-Tech |
|---|---|
| Series | A-Tech DDR2 Desktop Memory RAM |
| Capacity | 2GB (2 x 1GB) |
| Speed | DDR2 800 (PC2 6400) |
| Tested Frequency | 800 |
| Voltage | 1.80V |
| ECC | No |
| Buffered/Registered | Unbuffered |
| Multi-channel Kit | Dual Channel Kit |
| Recommend Use | AMD & Intel Compatible |
إصدارات أخرى من هذا الطراز
نفس الفئة، بذاكرة أو مبرّد أو تردد مختلف — قارن قبل أن تقرر.
These modules use the standard 240-pin DDR2 DIMM form factor, so they install in any desktop board with DDR2 240-pin slots.
Align the notch on each module with the slot key, press down firmly until both side clips snap shut; the step often missed is not pressing hard enough to engage both clips.
No firmware is involved; the memory runs at the standard 1.8V and only needs replacement if a module fails or you want more capacity.
أيضًا في هذا القسم
نفس القسم، ونفس صفحة الدفع — ثماني عملات رقمية وقفل سعر لمدة 30 دقيقة.
ما تدفعه، وما تُعرض به الأسعار.
يُرسَل من محفظتك عند إتمام الطلب
للعرض فقط — أسعار الكتالوج بالدولار الأمريكي
لا توجد عملة مطابقة.
اختر اللغة التي يخاطبك بها الموقع.
هل أنت جديد هنا؟
لديك حساب بالفعل؟
لا توجد إعادة تعيين تلقائية: هذا المتجر لا يُرسل أي بريد، فلا يوجد رابط لمرة واحدة يمكن طلبه. اترك العنوان في الحساب، وسيُعالَج الأمر يدويًا.
تم تسجيل الطلب
لا شيء في طريقه إلى بريدك الوارد — هذا المتجر لا يُرسل أي بريد إطلاقًا. يتولّى أحدهم معالجة هذه الطلبات يدويًا.
تذكّرتها؟