Přijímáme kryptoměny — takže to, co držíte, můžete utratit za skutečný hardware.Plaťte kryptem, utrácejte ho za skutečný hardware. Pojištěná doprava zdarma po celém světě nad 399 $. Neutrální přepravní krabice bez loga, odesílané z Německa.Pojištěná doprava zdarma nad 399 $. Jakmile se otevře pokladna, je váš kurz zablokovaný na 30 minut.Kurz zablokovaný na 30 minut. Každý výrobek je zapečetěný, jeho sériové číslo je zkontrolované a vztahuje se na něj 24měsíční záruka.Zapečetěno, záruka 24 měsíců.

Sledované položky Přihlásit se
Rectangular bench power supply unit with dual digital displays and front panel controls

myVolts

myVolts STP6005D DC power supply 0-60V 0-5A factory maintenance

SKU CH-5D4F-48JAJ MPN STP6005D

Adjustable 0-60 V, 0-5 A DC supply with dual display, CV/CC auto-switching and short-circuit, over-temperature protection for bench and cabinet use

  • TypeAT
  • Continuous 0-60V and 0-5A adjustment for flexible bench testing
  • Automatic CV/CC crossover keeps output stable when load conditions change
  • Dual independent displays show voltage and current at a glance
  • Built-in current-limiting, short-circuit and over-temperature protection guards connected gear
  • Up to 80% efficiency reduces waste heat during extended maintenance sessions

Adjustable DC output 0-60 V 0-5 A

The myVolts STP6005D is a bench-top DC power supply that delivers continuously adjustable voltage from 0 to 60 V and current from 0 to 5 A. It operates in constant-voltage or constant-current mode with automatic crossover, and the dual display shows both values independently. Efficiency reaches 80 %. It is built for factory maintenance, calibration stations and integration into test cabinets.

Engineers and technicians needing precise

This unit suits engineers and technicians who require a regulated DC source for prototyping, repair or calibration work where fine voltage and current control matter. The 0.5 % + 3 mV line regulation and 50 mVrms ripple support sensitive analogue circuits. Buyers who need higher current, higher voltage, programmable sequencing or remote computer control should look at other equipment.

60 V maximum output voltage

The single specification that decides fit is the 60 V maximum output voltage combined with a 5 A current limit. If the device under test requires more than 60 V or more than 5 A, this supply cannot power it.

Přednosti

  • Continuous 0-60V and 0-5A adjustment for flexible bench testing
  • Automatic CV/CC crossover keeps output stable when load conditions change
  • Dual independent displays show voltage and current at a glance
  • Built-in current-limiting, short-circuit and over-temperature protection guards connected gear
  • Up to 80% efficiency reduces waste heat during extended maintenance sessions

Specifikace

TypeAT

Otázky k tomuto produktu

At what output current does the load-regulation spec change from 0.1% + 3mV to 0.2% + 5mV?

The load-regulation specification shifts at 3 A; below that it is 0.1% + 3mV, above it becomes 0.2% + 5mV.

What protection features activate during continuous full-load operation to manage heat and faults?

Over-temperature protection, short-circuit protection and current-limiting buck circuitry engage automatically during sustained use.

Which mains fuse must be present in the IEC inlet before the unit will power on?

A 5 A, 250 VAC slow-blow fuse (marked F5AL) is required in the inlet for the supply to operate.

Také v této kategorii

Zákazníci také porovnávali

Stejná kategorie, stejná pokladna — osm měn a kurz zamčený na 30 minut.