Přijímáme kryptoměny — takže to, co držíte, můžete utratit za skutečný hardware.Plaťte kryptem, utrácejte ho za skutečný hardware. Pojištěná doprava zdarma po celém světě nad 399 $. Neutrální přepravní krabice bez loga, odesílané z Německa.Pojištěná doprava zdarma nad 399 $. Jakmile se otevře pokladna, je váš kurz zablokovaný na 30 minut.Kurz zablokovaný na 30 minut. Každý výrobek je zapečetěný, jeho sériové číslo je zkontrolované a vztahuje se na něj 24měsíční záruka.Zapečetěno, záruka 24 měsíců.

Sledované položky Přihlásit se
Rectangular bench power supply with dual LED displays and front panel controls

myVolts

myVolts STP6005D High 0-60V 0-5A power supply

SKU CH-RSN0-1W2DA MPN STP6005D

Adjustable 0-60V, 0-5A DC power supply with dual display, CV/CC auto-switching and short-circuit, over-temperature and current-limit protection

  • TypeAT
  • Adjustable 0-60V output for flexible test setups
  • Continuous 0-5A current with automatic CV/CC switching
  • Dual independent displays show voltage and current simultaneously
  • Multiple protections include current limit, short-circuit and over-temperature
  • Up to 80% efficiency reduces heat in cabinet integration

Bench power supply for lab and test use

The myVolts STP6005D is a bench-top DC power supply with a continuously adjustable output of 0-60V and 0-5A. It operates in automatic constant voltage and constant current crossover mode. Independent dual displays show voltage and current simultaneously. Efficiency reaches 80 percent. Built-in protections include current-limiting buck, short-circuit and over-temperature safeguards.

Upgrade from fixed or single-range units

This supply replaces fixed-voltage adapters or single-range bench units when a wider 0-60V span and 0-5A current capability are required. The jump is worth it for calibration stations, factory maintenance benches and test cabinet integration where both voltage and current must be set precisely. Regulation rates of 0.5% plus 3mV for voltage and 0.2% plus 3mA for current support repeatable results.

Check mains fuse rating and operating limits

Verify that the AC input environment matches the 250VAC F5AL fuse specification. Confirm the ambient temperature stays within 0 to 40 degrees Celsius and relative humidity below 80 percent. Ensure the load does not exceed the 5A maximum and that the 50mVrms voltage ripple and 50mArms current ripple are acceptable for the intended test circuit.

Přednosti

  • Adjustable 0-60V output for flexible test setups
  • Continuous 0-5A current with automatic CV/CC switching
  • Dual independent displays show voltage and current simultaneously
  • Multiple protections include current limit, short-circuit and over-temperature
  • Up to 80% efficiency reduces heat in cabinet integration

Specifikace

TypeAT

Otázky k tomuto produktu

What bench space and fuse rating does the STP6005D require?

The unit runs on a standard bench at 0 to 40 °C ambient and uses an F5AL 250 VAC fuse for mains protection.

How do I set the STP6005D into constant-current mode without tripping the 0.5 % voltage regulation?

Adjust the current knob first, then raise voltage; the supply auto-switches to CC at the preset limit and holds 0.5 % + 3 mV line regulation.

When should the F5AL fuse or the 80 % efficiency thermal path be checked on the STP6005D?

Inspect the F5AL 250 VAC fuse after any overload event and verify airflow if the unit runs continuously above 3 A where load regulation shifts to 0.2 % + 5 mV.

Také v této kategorii

Zákazníci také porovnávali

Stejná kategorie, stejná pokladna — osm měn a kurz zamčený na 30 minut.