OWC 8GB DDR4 2133MHz CL15 1.2V 288pin UDIMM memory upgrade
- 8GB
- 288-Pin DDR4 Non-EC…
Vi tager imod kryptovaluta — så den krypto, du ejer, kan købe rigtig hardware.Betal med krypto, brug det på rigtig hardware. Gratis, forsikret levering til hele verden ved køb over 399 $. Neutrale, umærkede papkasser, sendt fra Tyskland.Gratis, forsikret levering over 399 $. Din kurs låses i 30 minutter, så snart kassen åbner.Kurs låst i 30 minutter. Hver vare er forseglet, har kontrolleret serienummer og er dækket af 24 måneders garanti.Forseglet, 24 måneders garanti.
OWC
8GB DDR4 2400 CL17 UDIMM compatible with HP ProDesk 400 G4 and 600 G3 systems
This 8GB DDR4 module is built for HP ProDesk 400 G4 SFF, 400 G4 Tower, 600 G3 SFF and 600 G3 Tower systems. It delivers a straightforward capacity increase for office workstations that need more memory headroom. The unbuffered UDIMM design fits standard desktop DIMM slots without requiring registered memory support. Buyers with other platforms or laptop SODIMM slots cannot use this part.
Operating at 1.2V, the module runs at the standard DDR4 voltage for low power draw and minimal heat output. No heat spreader is fitted, so airflow across the PCB handles cooling in typical chassis layouts. The CL17 latency at 2400MHz keeps timing overhead modest during sustained workloads. Noise is not a factor as the component has no moving parts.
The 288-pin DDR4 2400 PC4-19200 CL17 1.2V Non-ECC unbuffered 1Rx8 configuration determines fit and function. Systems must accept this exact speed, voltage, pin count and error-correction type. Backward compatibility with 2133MHz buses is supported. If your motherboard requires ECC, registered DIMMs, a different voltage or a different pin layout, this module will not work.
| Brand | OWC |
|---|---|
| Part Number | 2U4D41R808GB |
| Capacity | 8GB |
| Type | 288-Pin DDR4 Non-ECC UDIMM |
| Speed | DDR4 2400 (PC4 19200) |
| CAS Latency | CL17 |
| Voltage | 1.2V |
| ECC | No |
| Buffered/Registered | Unbuffered |
| Rank | 1Rx8 |
| Heat Spreader | No |
| Compatible System | HP ProDesk 400 G4 SFF HP ProDesk 400 G4 Tower HP ProDesk 600 G3 SFF HP ProDesk 600 G3 Tower |
Andre versioner af denne model
Samme familie, men med anden hukommelse, køler eller clockfrekvens — sammenlign, før du bestemmer dig.
Power off the PC, unplug it, open the case, align the notch on the module with the slot key, press firmly until both retention clips click shut, then power on and verify 2400 MHz operation in BIOS — the step most people miss is fully seating both clips.
No scheduled maintenance is required; the module has no heat spreader and no moving parts, so replacement is only necessary if a memory test reports errors or if you later expand beyond the board's maximum capacity.
The JEDEC-specified 1.2 V operating voltage and CL17 latency define the thermal and timing envelope; sustained loads stay within that envelope because the module is unbuffered and runs at standard desktop power levels.
Også på denne hylde
Samme hylde, samme kasse — otte mønter og 30 minutters kurslås.
Det du betaler med, og det du ser priserne i.
Sendes fra din tegnebog i kassen
Kun til visning — kataloget er prissat i USD
Ingen valuta matcher det.
Vælg det sprog, siden taler til dig på.
Ingen sprog matcher.
Ny her?
Har du allerede en?
Der findes ingen automatisk nulstilling: denne butik sender ingen e-mails, så der er intet engangslink at bede om. Efterlad adressen på kontoen, så bliver den behandlet manuelt.
Anmodning registreret
Der er intet på vej til din indbakke — denne butik sender slet ingen e-mails. Nogen behandler dem manuelt.
Kom du i tanke om den?