OWC 8GB DDR4 2133MHz CL15 1.2V 288pin UDIMM memory upgrade
- 8GB
- 288-Pin DDR4 Non-EC…
We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.
OWC
8GB DDR4 2400 CL17 UDIMM compatible with HP ProDesk 400 G4 and 600 G3 systems
This 8GB DDR4 module is built for HP ProDesk 400 G4 SFF, 400 G4 Tower, 600 G3 SFF and 600 G3 Tower systems. It delivers a straightforward capacity increase for office workstations that need more memory headroom. The unbuffered UDIMM design fits standard desktop DIMM slots without requiring registered memory support. Buyers with other platforms or laptop SODIMM slots cannot use this part.
Operating at 1.2V, the module runs at the standard DDR4 voltage for low power draw and minimal heat output. No heat spreader is fitted, so airflow across the PCB handles cooling in typical chassis layouts. The CL17 latency at 2400MHz keeps timing overhead modest during sustained workloads. Noise is not a factor as the component has no moving parts.
The 288-pin DDR4 2400 PC4-19200 CL17 1.2V Non-ECC unbuffered 1Rx8 configuration determines fit and function. Systems must accept this exact speed, voltage, pin count and error-correction type. Backward compatibility with 2133MHz buses is supported. If your motherboard requires ECC, registered DIMMs, a different voltage or a different pin layout, this module will not work.
| Brand | OWC |
|---|---|
| Part Number | 2U4D41R808GB |
| Capacity | 8GB |
| Type | 288-Pin DDR4 Non-ECC UDIMM |
| Speed | DDR4 2400 (PC4 19200) |
| CAS Latency | CL17 |
| Voltage | 1.2V |
| ECC | No |
| Buffered/Registered | Unbuffered |
| Rank | 1Rx8 |
| Heat Spreader | No |
| Compatible System | HP ProDesk 400 G4 SFF HP ProDesk 400 G4 Tower HP ProDesk 600 G3 SFF HP ProDesk 600 G3 Tower |
Other versions of this model
Same family, different memory, cooler or clock — compare before you commit.
Power off the PC, unplug it, open the case, align the notch on the module with the slot key, press firmly until both retention clips click shut, then power on and verify 2400 MHz operation in BIOS — the step most people miss is fully seating both clips.
No scheduled maintenance is required; the module has no heat spreader and no moving parts, so replacement is only necessary if a memory test reports errors or if you later expand beyond the board's maximum capacity.
The JEDEC-specified 1.2 V operating voltage and CL17 latency define the thermal and timing envelope; sustained loads stay within that envelope because the module is unbuffered and runs at standard desktop power levels.
Also in this aisle
Same shelf, same checkout — eight coins and a 30-minute rate lock.
What you pay in, and what you read prices in.
Sent from your wallet at checkout
Display only — the catalogue is priced in USD
No currency matches that.
Pick the language the site speaks to you in.
No language matches that.
New here?
Already have one?
There is no automatic reset: this shop sends no mail, so there is no one-time link to ask for. Leave the address on the account and it gets picked up by hand.
Request noted
Nothing is on its way to your inbox — this shop sends no mail at all. Someone picks these up by hand.
Remembered it?