BFKK
BFKK 3U Rackmount Server Chassis EATX/ATX/MATX 4x5.25 6x3.5 Top/Side Cooling
- Rackmount
214,99 US$
0.00276138BTC
En stock
NEMIX RAM
NEMIX RAM 16GB DDR4 3200 CL22 2Rx8 260-pin SODIMM for POSIFLEX ZT-3115
A 16GB DDR4 3200 SODIMM with CL22 latency and 1.2V operation, built for POSIFLEX ZT-3115 terminals
- Capacity16GB
- SpeedDDR4 3200 (PC4 25600)
- ECCNo
- Buffered/RegisteredUnbuffered
- ChipsetMajor OEM Samsung, Micron, Hynix
- Voltage1.20V
- 16 GB DDR4 3200 MHz boosts POS terminal responsiveness
- CL22 latency at 1.2 V keeps power draw low
- 2Rx8 260-pin SODIMM fits POSIFLEX ZT-3115 slot directly
- Samsung, Micron or Hynix chips ensure stable operation
- Non-ECC unbuffered design simplifies drop-in installation
POSIFLEX ZT-3115 compatible SODIMM
This 16GB DDR4 3200 module is built specifically for the POSIFLEX ZT-3115 Haydn ZT series POS terminal. It installs as a single 260-pin SODIMM to add 16GB of system memory in one slot. The non-ECC unbuffered design matches the terminal's motherboard requirements. It is not intended for desktop DIMM slots or for systems that require registered or ECC memory.
Low-voltage DDR4 operation
The module runs at 1.2V with a CL22 latency rating at 3200MT/s (PC4-25600). Standard DDR4 voltage keeps power draw modest and heat output low without a heat spreader. The 2Rx8 organisation uses major OEM chips from Samsung Micron or Hynix and is stress-tested under load for stability. It produces no fan noise because it has no active cooling.
Single-slot upgrade for the ZT series
The SODIMM fits the terminal's 260-pin DDR4 slot and frees any second slot for future expansion if the board provides one. No extra cables brackets or adapters are needed. The 1.20V supply is provided by the motherboard so no external power is required. Builders who need ECC registered modules or a different pin count cannot use this kit.
Puntos fuertes
- 16 GB DDR4 3200 MHz boosts POS terminal responsiveness
- CL22 latency at 1.2 V keeps power draw low
- 2Rx8 260-pin SODIMM fits POSIFLEX ZT-3115 slot directly
- Samsung, Micron or Hynix chips ensure stable operation
- Non-ECC unbuffered design simplifies drop-in installation
Especificaciones
| Brand | NEMIX RAM |
|---|---|
| Series | POSIFLEX POS Series Point of Sale Kiosk Memory |
| Model | POSIFLEX POS DDR4 3200MHZ Non-ECC Unbuffered SODIMM |
| Part Number | MS25600-628K1 |
| Capacity | 16GB |
| Speed | DDR4 3200 (PC4 25600) |
| ECC | No |
| Buffered/Registered | Unbuffered |
| Chipset | Major OEM Samsung, Micron, Hynix |
| Voltage | 1.20V |
| Compatible System | POSIFLEX POS |
| CAS Latency | CL22 |
| Heat Spreader | No |
| Type | 260-Pin DDR4 SODIMM |
| Rank | 2Rx8 |
| Features | DDR4 Non-ECC Unbuffered SODIMM Motherboard Compatible |
| Package Content | 16GB (1X16GB) DDR4 3200MHZ PC4-25600 2Rx8 1.2V CL22 260-PIN Non-ECC Unbuffered SODIMM |
Preguntas sobre este artículo
How do I install the 260-pin SODIMM in the POSIFLEX ZT-3115 and which step is often missed?
Power off the terminal, remove the bottom cover, align the notch on the 260-pin module with the slot key, press firmly until both side clips click, then replace the cover; the step most often missed is pressing hard enough to fully seat both clips.
What maintenance or replacement will this 16GB DDR4 module need later?
No routine maintenance is required; if a memory error appears, run a diagnostic and replace the module, otherwise it runs for the life of the terminal.
What limit appears first on this CL22 1.2V kit under sustained workloads?
The CAS latency of 22 cycles at 3200 MT/s sets the response-time floor, so latency-sensitive tasks hit that timing ceiling before bandwidth or voltage limits.
También en este pasillo
Los clientes también compararon
Mismo estante, mismo pago — ocho criptomonedas y un tipo de cambio fijado 30 minutos.
BFKK
BFKK 2U Micro ATX Rackmount 2×5.25" 4×3.5" Side 80mm Fan
- Rackmount
216,99 US$
0.00278707BTC
En stock
