Aceptamos criptomonedas — así, las criptos que usted tiene pueden comprar hardware real.Pague en cripto y gástela en hardware real. Envío asegurado gratis a nivel mundial a partir de $399. Cajas neutras, sin marca, enviadas desde Alemania.Envío asegurado gratis a partir de $399. Su cotización queda bloqueada 30 minutos en cuanto se abre el pago.Cotización bloqueada 30 minutos. Todos los artículos vienen sellados, con el número de serie verificado y cubiertos por una garantía de 24 meses.Sellado, con 24 meses de garantía.

Artículos guardados Iniciar sesión
Green circuit board with black memory chips and gold edge connectors

OWC

OWC 8GB DDR4 2133MHz CL15 1.2V 288pin UDIMM for HP Envy Phoenix 860

SKU CH-D1F1-B0SD2

8GB DDR4 2133MHz CL15 UDIMM adds 8GB of 1.2V non-ECC memory to HP Envy Phoenix 860 desktops

  • Capacity8GB
  • Type288-Pin DDR4 Non-ECC UDIMM
  • SpeedDDR4 2133 (PC4 17000)
  • CAS LatencyCL15
  • Voltage1.2V
  • ECCNo
  • 8GB DDR4 2133MHz CL15 boosts multitasking speed
  • 2V low-voltage design reduces power draw
  • 288-pin UDIMM fits HP Envy Phoenix 860 series
  • JEDEC compliant for warranty-safe upgrades
  • Unbuffered non-ECC module installs easily in desktop PCs

HP Envy Phoenix 860 compatible DDR4 UDIMM

This 8 GB DDR4 module is built for HP Envy Phoenix 860-036ng, 860-041ng, 860-050nc, 860-070na and 860-080no desktops. It runs at 2133 MHz with CL15 latency at the standard 1.2 V. The unbuffered, non-ECC design matches the factory specification for these systems.

Steady operation at JEDEC standard speed

The module operates continuously at the rated 2133 MHz without overclocking headroom. CL15 timing and 1.2 V voltage are fixed by the JEDEC PC4-17000 standard, so sustained workloads see consistent bandwidth. No heat spreader is fitted, relying on case airflow for thermal management during extended use.

Simple slot installation with model verification

The 288-pin UDIMM seats in the standard desktop DIMM slot; alignment notch prevents backwards insertion. Most issues arise when the specific Phoenix 860 sub-model is not confirmed against the supported list above. Builders needing ECC, registered memory or speeds above 2133 MHz should look elsewhere.

Puntos fuertes

  • 8GB DDR4 2133MHz CL15 boosts multitasking speed
  • 2V low-voltage design reduces power draw
  • 288-pin UDIMM fits HP Envy Phoenix 860 series
  • JEDEC compliant for warranty-safe upgrades
  • Unbuffered non-ECC module installs easily in desktop PCs

Especificaciones

BrandOWC
Part Number2U1D42R808GB
Capacity8GB
Type288-Pin DDR4 Non-ECC UDIMM
SpeedDDR4 2133 (PC4 17000)
CAS LatencyCL15
Voltage1.2V
ECCNo
Buffered/RegisteredUnbuffered
Rank2Rx8
Heat SpreaderNo
Compatible SystemHP ENVY Phoenix 860-036ng
HP ENVY Phoenix 860-041ng
HP ENVY Phoenix 860-050nc
HP ENVY Phoenix 860-070na
HP ENVY Phoenix 860-080no

Otras versiones de este modelo

5 más en esta gama

Misma familia, con memoria, disipador o frecuencia diferentes — compare antes de decidirse.

Preguntas sobre este artículo

Does the 1.2V DDR4 module run hot or draw extra power during all-day use?

The module operates at the standard 1.2V DDR4 voltage with no heat spreader, so power draw and heat stay at JEDEC baseline levels for continuous desktop workloads.

My HP Envy Phoenix 860 motherboard has four 288-pin slots — is anything else required to add this stick?

The board must support DDR4 2133MHz unbuffered non-ECC UDIMMs; if it does, the 288-pin module seats directly with no extra cables, brackets or firmware steps.

Will this 2133MHz CL15 stick down-clock reliably alongside the original 2133MHz memory already in my 860-050nc?

Yes — it matches the factory 2133MHz speed and CL15 timing, so the memory controller runs all populated slots at the same JEDEC profile without manual adjustment.

También en este pasillo

Los clientes también compararon

Mismo estante, mismo pago — ocho criptomonedas y un tipo de cambio fijado 30 minutos.