Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Black standalone duplicator unit with four drive slots and front control panel

Systor

Systor 1 to 3 SATA NVMe Duplicator 18GB/min Standalone SYSNVME-XW303

SKU CH-THGW-3T795

Standalone duplicator copies or sanitises one source to three SATA or NVMe targets at up to 18 GB/min

  • Target1 to 3
  • Data Transfer Rate18GB/min
  • Operating TypeStandalone

TARGET SIZE 1 to 03

DATA TRANSFER RATE 18.0GB/min [300MB/sec]

  • Standalone operation — no computer or software needed
  • Copies up to three drives at 18 GB per minute
  • Supports SATA and NVMe drives including 2.5 and 3.5 inch formats
  • Multiple sanitise modes including NIST 800-88 and DoD 5220.22-M
  • Open platform design fits M.2, PCIe and SATA devices

Standalone NVMe and SATA Duplicator

The Systor SYSNVME-XW303 is a standalone duplicator that copies or sanitises one source drive onto up to three targets. It accepts NVMe M.2 and SATA SSDs or HDDs in 2.5 and 3.5 inch form factors without requiring a host computer. Transfer rates reach 18GB per minute.

IT teams and forensic units needing multi-drive

Organisations that must duplicate or wipe several drives at once will benefit from the three-target capacity and support for both NVMe and SATA media. Buyers who need more than three simultaneous targets or who rely on unsupported interfaces such as USB cannot use this unit.

18GB per minute maximum copy speed

The quoted 18GB/min throughput determines how quickly large drives can be cloned or erased. Actual performance depends on the read and write capabilities of the specific source and target drives installed.

Kohokohdat

  • Standalone operation — no computer or software needed
  • Copies up to three drives at 18 GB per minute
  • Supports SATA and NVMe drives including 2.5 and 3.5 inch formats
  • Multiple sanitise modes including NIST 800-88 and DoD 5220.22-M
  • Open platform design fits M.2, PCIe and SATA devices

Tekniset tiedot

Target1 to 3
Data Transfer Rate18GB/min
Operating TypeStandalone

Tämän mallin muut versiot

5 lisää samasta mallistosta

Sama tuoteperhe, eri muisti, jäähdytin tai kellotaajuus — vertaile ennen päätöstä.

Kysymyksiä tästä tuotteesta

How much power does the SYSNVME-XW303 draw when copying to three targets continuously?

The duplicator runs standalone without a host PC, so its power draw depends on the drives installed; no host software or computer is needed during long copy sessions.

Which drive interfaces must I already have to use the duplicator without extra adapters?

The unit accepts M.2 NVMe, M.2 SATA, and 2.5 or 3.5 inch SATA drives directly; mSATA or CFAST require separate adapters.

Will the duplicator copy from an older 2.5-inch SATA SSD to a new M.2 NVMe drive?

Yes, it automatically detects NVMe or SATA signals and supports cross-interface duplication such as SATA SSD to M.2 NVMe.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.