暗号資産でのお支払いに対応—お手持ちのコインで、本物のハードウェアをご購入いただけます。暗号資産で支払い、本物のハードウェアに使う。 $399以上のご注文で、世界中どこでも送料無料（保険付き）。無地・ノーブランドの外箱で、ドイツから発送いたします。$399以上で送料無料（保険付き）。 注文手続きを開始すると、レートは30分間ロックされます。レートは30分間ロック。 すべての商品は未開封で、シリアル番号を確認した上で、24か月保証が付いています。未開封、24か月保証。

ウォッチリスト ログイン
Two green circuit boards with black chips, no heat spreaders

NEMIX RAM

NEMIX RAM 32GB (2x16GB) DDR4 2933MHz CL21 1.2V 288-pin UDIMM for Supermicro X12SAE X12SCA-F memory upgrade

SKU CH-E93S-XF1W9

32 GB dual-channel DDR4 kit running at 2933 MHz with CL21 timing, built for Supermicro X12SAE and X12SCA-F motherboards

  • Capacity32GB (2 x 16GB)
  • Type288-Pin DDR4 UDIMM
  • SpeedDDR4 2933 (PC4 23400)
  • CAS LatencyCL21
  • Voltage1.20V
  • ECCNo

Size 32GB 2X16GB

  • 32 GB dual-channel kit doubles capacity for Supermicro X12SAE and X12SCA-F boards
  • DDR4-2933 CL21 timing matches the motherboard's rated speed and latency
  • 20 V operation keeps power draw low on the desktop platform
  • Built with Samsung, Micron or Hynix ICs for stable performance at rated specs
  • 288-pin UDIMM form factor fits the exact DIMM slots your board requires

Exact-match DDR4 upgrade kit

This 32 GB kit contains two 16 GB DDR4 2933 MHz modules built to the CL21 1.2 V 288-pin UDIMM specification your Supermicro X12SAE or X12SCA-F motherboard expects. Major OEM chips from Samsung Micron or Hynix are tested at rated speed timing and voltage so the memory controller recognises full capacity immediately.

Replaces slower or smaller DDR4 DIMMs

If your board currently runs lower-frequency DDR4 or has empty slots this kit lifts bandwidth to PC4-23400 without changing voltage or form factor. The 1Rx8 rank layout matches the population rules in the motherboard manual so the upgrade is recognised at full speed on first boot.

Suits Supermicro X12SAE and X12SCA-F owners

Builders who need ECC registered modules or SODIMM form factor should look elsewhere because this kit is non-ECC unbuffered UDIMM only. Systems that require a different DDR generation or a higher density per DIMM than 16 GB will not be compatible.

特長

  • 32 GB dual-channel kit doubles capacity for Supermicro X12SAE and X12SCA-F boards
  • DDR4-2933 CL21 timing matches the motherboard's rated speed and latency
  • 20 V operation keeps power draw low on the desktop platform
  • Built with Samsung, Micron or Hynix ICs for stable performance at rated specs
  • 288-pin UDIMM form factor fits the exact DIMM slots your board requires

仕様

BrandNEMIX RAM
SeriesNEMIX RAM Original Series Memory
ModelDDR4 Non-ECC Unbuffered UDIMM Memory
Part NumberMD23400-618K2
Capacity32GB (2 x 16GB)
Type288-Pin DDR4 UDIMM
SpeedDDR4 2933 (PC4 23400)
CAS LatencyCL21
Voltage1.20V
ECCNo
Buffered/RegisteredUnbuffered
Rank1Rx8
ChipsetMajor OEM Samsung, Micron, Hynix
Heat SpreaderNo
Compatible SystemSupermicro
FeaturesDDR4 Non-ECC Unbuffered UDIMM Motherboard Compatible
Package Content32GB 2X16GB DDR4 2933MHz PC4-23400 1Rx8 1.2V 288-PIN Non-ECC UDIMM KIT

このモデルの他のバージョン

同シリーズにさらに 5点

同じファミリーで、メモリ・クーラー・クロックが異なります — 購入前に比較してください。

この商品に関する質問

What slot type and pin count does this 32 GB kit require on the Supermicro X12SAE or X12SCA-F?

It uses standard 288-pin DDR4 UDIMM slots; each module is a 16 GB 1Rx8 stick, so two free DIMM sockets are needed.

What is the correct installation order for the two 16 GB modules on these Supermicro boards?

Populate the slots specified in the motherboard manual for a two-DIMM configuration — typically the same-channel pair — so the memory controller sees both 1Rx8 ranks at 2933 MHz.

Will the modules need any firmware updates or component replacements during their service life?

No firmware is involved; the DRAM chips (Samsung, Micron or Hynix) and PCB are solid-state, so only physical reseating or full replacement would ever be required.

同じ売り場の商品

よく比較されている商品

同じ売り場、同じレジ — 8種類のコインと30分間のレートロック。