暗号資産でのお支払いに対応—お手持ちのコインで、本物のハードウェアをご購入いただけます。暗号資産で支払い、本物のハードウェアに使う。 $399以上のご注文で、世界中どこでも送料無料（保険付き）。無地・ノーブランドの外箱で、ドイツから発送いたします。$399以上で送料無料（保険付き）。 注文手続きを開始すると、レートは30分間ロックされます。レートは30分間ロック。 すべての商品は未開封で、シリアル番号を確認した上で、24か月保証が付いています。未開封、24か月保証。

ウォッチリスト ログイン
Small ceramic cylinder 6.35mm diameter 20mm long with 100cm wire lead

ProTechTrader

ProTechTrader 12V 40W 6.35mm Ceramic Cartridge Heater MK10 3d printers accessory

SKU CH-A4ZC-XA3T1

12V 40W ceramic cartridge heater with 6.35mm diameter and 20mm length fits MK10 extruders on Wanhao Duplicator i3, FlashForge Creator and Monoprice Maker Select printers

  • 12 V 40 W output gives fast heat-up for MK10 hot-ends
  • 35 mm diameter matches standard 1/4 in heater-block bores
  • 20 mm cartridge length fits common MK10 extruder housings
  • 100 cm wire allows flexible routing to controller boards
  • Compatible with Wanhao Duplicator i3 and FlashForge Creator printers

Ceramic Cartridge Heater MK10

This ProTechTrader ceramic cartridge heater supplies 40 watts at 12 volts for MK10 extruders. It has a 6.35 millimetre diameter and a 20 millimetre length with a 100 centimetre wire lead. The part is designed as a direct OEM fit for printers that use a 1/4 inch heater block bore. It is sold new as a single replacement component.

Compatibility and limits

The heater fits Wanhao Duplicator i3, FlashForge Creator and Monoprice Maker Select v1, v2 and v2.1 machines that have a 1/4 inch heater hole. Printers with a different bore size, a different voltage requirement or a non-MK10 hotend will not accept this cartridge. Buyers who need a higher wattage, a different diameter or a shorter wire length should look at something else.

Pre-installation checks

Verify that your hotend block has a 6.35 millimetre bore and that the printer runs a 12 volt heater circuit. Confirm the existing cartridge measures 20 millimetres in length so the replacement seats fully. Ensure the 100 centimetre wire reach suits your cable routing and that the connector type matches your control board.

特長

  • 12 V 40 W output gives fast heat-up for MK10 hot-ends
  • 35 mm diameter matches standard 1/4 in heater-block bores
  • 20 mm cartridge length fits common MK10 extruder housings
  • 100 cm wire allows flexible routing to controller boards
  • Compatible with Wanhao Duplicator i3 and FlashForge Creator printers

仕様

BrandProTechTrader
Modelch12v40w-25

この商品に関する質問

What voltage and wattage must my printer's power supply provide for this 12V 40W cartridge heater?

The heater requires a 12 volt supply capable of delivering 40 watts, so check that your printer's board and PSU can provide that power on the hot-end output.

Will this 6.35mm diameter heater fit the bore in my MK10 hot-end block?

Yes, it is made for MK10 extruders with a 6.35 mm (1/4 inch) heater-block bore, matching printers such as Wanhao Duplicator i3 and FlashForge Creator.

How can I verify the heater is working correctly after installation?

Heat the hot-end to your normal printing temperature and confirm it reaches and holds that temperature without thermal runaway errors or excessive overshoot.

同じ売り場の商品

よく比較されている商品

同じ売り場、同じレジ — 8種類のコインと30分間のレートロック。