저희는 암호화폐로 결제를 받습니다 — 보유하신 코인으로 실제 하드웨어를 구매하실 수 있습니다.암호화폐로 결제하고, 실제 하드웨어 구매에 사용하십시오. 전 세계 어디서나 US$399 이상 구매 시 무료 보험 배송. 무지 상자에 담아 독일에서 발송합니다.US$399 이상 구매 시 무료 보험 배송. 체크아웃을 시작하면 30분 동안 환율이 잠깁니다.30분간 환율 잠금. 모든 제품은 밀봉된 상태로 일련번호를 확인한 후 24개월 보증을 제공합니다.밀봉 포장, 24개월 보증.

가격 추적 로그인

myVolts

myVolts 1800W ATX Mining Power Supply 10×12V 14cm Fan

SKU CH-1HD5-BSGR6

An 1800 W ATX unit with ten 12 V connectors, active PFC, six protection circuits and a 14 cm quiet fan

  • TypeAT
  • Delivers 1800W for high-density mining rigs
  • Ten 12 V connectors power multiple graphics cards
  • Active PFC corrects input from 180 to 240 V
  • Six safety circuits guard against voltage and current faults
  • 14 cm fan cools quietly with insect-resistant grille

Mining power supply 1800W

This ATX power supply delivers 1800W for multi-GPU mining rigs. It operates on 180-240V input with active PFC and a dual 12V rail design based on the 12V 2.3 specification. The unit includes ten 6-pin connectors for graphics cards and a 6-pin CPU power interface.

Upgrade from lower-wattage ATX units

Replaces standard desktop power supplies when a build needs more than ten 12V outputs for mining cards. The jump is worth it when a single rail cannot feed all GPUs or when the existing unit lacks the 12V 2.3 dual-rail layout required by the motherboard and graphics interfaces.

Ten 12V outputs with six protections

Comfortably handles mining configurations that demand ten simultaneous 6-pin connections under continuous load. Over-voltage, under-voltage, over-current, overload, short-circuit and anti-thunder protections guard the system. Headroom runs out when the total draw exceeds 1800W or when additional connector types beyond 6-pin are required.

주요 특징

  • Delivers 1800W for high-density mining rigs
  • Ten 12 V connectors power multiple graphics cards
  • Active PFC corrects input from 180 to 240 V
  • Six safety circuits guard against voltage and current faults
  • 14 cm fan cools quietly with insect-resistant grille

사양

TypeAT

이 상품에 대한 질문

What form factor does this 1800W unit use and will it fit a standard ATX case?

The supply follows the ATX 12V 2.0 standard and includes a 14cm fan, so it matches the depth and mounting holes of a regular ATX power supply.

Which cables must be connected first when installing this mining PSU to avoid a no-post situation?

Plug the 24-pin ATX motherboard cable and the 6-pin CPU power connector before attaching any of the ten 12V graphics-card leads; the board will not initialise without both primary feeds.

How often should the 14cm cooling fan be cleaned in a dusty mining environment?

Remove the side panel and blow compressed air through the fan grille every three to six months; the anti-insect grille reduces blockages but fine dust still builds up on the blades.

이 진열대의 다른 상품

고객들이 함께 비교한 상품

같은 진열대, 같은 체크아웃 — 코인 8종, 환율 잠금 30분.