Intel DC S3610 SSDSC2BX016T401 1.6TB 2.5" SATA enterprise SSD
- 2.5"
- 1.6TB
We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.
Intel
A 2.5 inch SATA internal SSD with 240GB capacity, up to 560 MBps sequential read, 480 MBps sequential write, AES 256-bit hardware encryption and 1,600,000 hours MTBF
The Intel Pro 5400s is a 2.5 inch internal solid state drive with a 240GB capacity. It connects through a SATA III interface rated at 600 MBps. The drive uses TLC memory built on 16nm lithography and includes hardware based AES 256-bit encryption. It is designed for consumer workloads in standard drive bays.
Under continuous operation the drive draws a typical 90 mW active power and 50 mW at idle. Operating temperature spans 0°C to 70°C. The controller maintains read and write latency at 50 µs. Endurance is rated at a mean time between failures of 1,600,000 hours, reflecting steady state reliability rather than short burst peaks.
Sequential throughput caps at 560 MBps read and 480 MBps write, which sits at the ceiling of the SATA 3.0 6Gbps link. Random performance reaches 74,000 IOPS read and 85,000 IOPS write for 4KB blocks. These figures represent the practical boundary of the interface, so the drive cannot exceed them regardless of workload intensity.
| Brand | Intel |
|---|---|
| Series | Pro 5400s |
| Model | SSDSC2KF240H6X1 |
| Device Type | Internal Solid State Drive (SSD) |
| Used For | Consumer |
| Form Factor | 2.5" |
| Capacity | 240GB |
| Memory Components | TLC |
| Interface | SATA III |
| Max Sequential Read | Up to 560 MBps |
| Max Sequential Write | Up to 480 MBps |
| 4KB Random Read | Up to 74,000 IOPS |
| 4KB Random Write | Up to 85,000 IOPS |
| Read Latency | 50 µs |
| Write Latency | 50 µs |
| MTBF | 1,600,000 hours |
| Features | Lithography Type: 16nm Hardware Encryption: AES 256-bit |
| Power Consumption (Idle) | 50 mW Typical |
| Power Consumption (Active) | 90 mW Typical |
| Operating Temperature | 0°C ~ +70°C |
| Max Shock Resistance | 1500G / 0.5 ms |
| Max Vibration Resistance | Operating: 2.17 GRMS (5 - 700 Hz) Non-Operating: 3.13 GRMS (5 - 800 Hz) |
| Height | 7.00mm |
The drive typically draws 50 mW at idle and 90 mW during active use, so heat output stays very low even after hours of continuous operation.
It requires a standard SATA 3.0 6Gb/s port and a matching SATA power connector from the power supply.
The drive is backward compatible with SATA 3Gb/s ports; sequential speeds will simply scale down to the link limit while random performance and latency remain unchanged.
Also in this aisle
Same shelf, same checkout — eight coins and a 30-minute rate lock.
What you pay in, and what you read prices in.
Sent from your wallet at checkout
Display only — the catalogue is priced in USD
No currency matches that.
Pick the language the site speaks to you in.
New here?
Already have one?
There is no automatic reset: this shop sends no mail, so there is no one-time link to ask for. Leave the address on the account and it gets picked up by hand.
Request noted
Nothing is on its way to your inbox — this shop sends no mail at all. Someone picks these up by hand.
Remembered it?